Jump to content
SAU Community

3 Defi Gauges...

bugger

By bugger,
in Exterior & Interior Styling

 Share

Recommended Posts

alpinestars Experienced

alpinestars

Posted
Posted
yah... but...

isn't this way of placement is defect?

tot of using a gauge holder on the dash, due to the untidyness of the wires.

nope have been through booze buses and rbts and they dont say anything

pods look shit on the dash brackets look better

if you know to hide and neaten wires it doesnt look crap

  • 2 months later...
Sambo33 Grand Master

Sambo33

Posted
Posted
what brand etc is your gauge on the right top of the steering wheel? im looking for something exactly the same as that. and where did you get it from?

ta

looks like a HKS gauge :turned:

anyone else have any pics of tripple gauge installs? im looking to do mine soon, only with blitz gauges.

gotRICE? Veteran

gotRICE?

Posted
Posted (edited)

Personally i think having 3 gagues on the pillar looks a bit much.

I didnt read everything but the way i see it, if your into the track, like i am, having the gagues on the DIN of the headunit makes you look away from the road for too long, as you almost have to turn your head and look down. (actually, even on the street, where it could cause more problems!)

Whereas on the pillar you barely have to glance at them to see whats going on.

This is the Setup on my old ITR. I custom made the pods, and it didnt obstruct the view too much as to become a problem.

gagueoff.jpg

gagueon.jpg

If id had my way they would have hugged the pillar more, but it was hard work as it was :P

Yes POS Autogague ones :P But they were more for piece of mind that i wasnt going to skyrocket oil temps or loose pressure, i just read them as if it went a hell of alot higher than normaland kept going, it was getting warm. (Read 90deg normal, 140 after 20-30 mins track :D )

I dont have experience with Dash mounted ones, but IMHO they look like ass unless you have an OEM gage holder like R34's have. Then it looks nice.

Edited by gotRICE?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...