Jump to content
SAU Community

New 0-300kph 4wd Record

2rismo

By 2rismo,
in General Automotive Discussion

 Share

Recommended Posts

2rismo Grand Master

2rismo

Posted
Posted

Team Cowie - 12.474 seconds!!

At TOTB we broke the 4wd 0-300kph time held by Veilside Japan there time was 13s and we set a new record going from 0-300 kph in 12.474sec.

I took it all the way to over 200mph here is some of the data taken from the timing gear.

0-30 1.226

0-60 2.539

0-100 4.346

0-150 8.085

0-200 14.751

Some photos just before we took the Veilside 0-300 record.

IMGP0818.jpg

cruise-278.jpg

cruise-289.jpg

cruise-290.jpg

IMGP0716.jpg

IMGP0650.jpg

IMGP0877.jpg

totb200301.jpg

Link to comment
https://www.sau.com.au/forums/topic/179320-new-0-300kph-4wd-record/
Share on other sites
2rismo Grand Master

2rismo

Posted
  • Author
Posted
ummm didnt the veilside car do it on nittos?

You've got to be kidding me?!?!?

This is an OUTRIGHT record. How can it be any clearer than that?!?! Besides, slicks do VERY little to improve how fast you can reach a particular terminal speed.

Lithium Grand Master

Lithium

Posted
Posted
You've got to be kidding me?!?!?

This is an OUTRIGHT record. How can it be any clearer than that?!?! Besides, slicks do VERY little to improve how fast you can reach a particular terminal speed.

So the fact that the Heat Treatments GTR reached 300kph in under 7.6s isn't taken as a record because it wasn't targetting 0-300kph?

skybarge Community Regular

skybarge

Posted
Posted

Very nice good to see the old R32s still getting publicity :thanks:

so fastest 1/4 mile street and drag, fastest 0-300 oh yeah :)

For the dude above, the Veilside car was an R34, did it over here in NZ, just below Taupo, think the same year a Porsche crashed spectacularly on the same circuit :)

GTR:

Couldn't find the porsche crash though :down:

VB- Veteran

VB-

Posted
Posted (edited)

yeh the one im talking about was the grey R32, 13.72 was the time beer baron, dont think it was on slicks when it did it and had a strange miss-fire halfway through second.

and i think slicks would make a differnce as to how quick you reach a certain speed, 0-300 is a timed event, slicks = less time wheel spinning, and more time on the power, means you get to that speed in less time. unless you want to get into maths/physics with rolling resistance at higher speed etc, i really cant see how it wouldnt make a difference

i know you like your drag racing, go run on a set of $30 retreads vs some real good tyres. 0-300 is basically the same format as drag racing, just with a different goal

Edited by VB-

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...