Jump to content
SAU Community

Installing A Thermo Electric Fan

PyroIndustries

By PyroIndustries,
in General Maintenance

 Share

Recommended Posts

PyroIndustries Contributor

PyroIndustries

Posted
Posted

In my R33 skyline the clutch in my fan has had it.

I was thinking instead of replacing the standard fan i should just throw in a thermo electric fan

was thinking one 14" fan

or should i have 2 smaller ones?

any advice would be nice

thanks

Link to comment
https://www.sau.com.au/forums/topic/180675-installing-a-thermo-electric-fan/
Share on other sites
4drftn Experienced

4drftn

Posted
Posted

i dunno if this is the case with the skyline motors but in the old holden motors (253ci,308ci) disabling your engine fan and using thermos can increase hp (less drag, more efficiant)... slightly

anyway... are you putting one/them in front of your radiator? or infront of your engine?

Bliksem Veteran

Bliksem

Posted
Posted

Dont install two small ones unless you use the EF/EL setup that comes with the shroud. Other than that a single 16" fits the factory shroud and will flow as much if not more than the factory crank fan.

Theres a DIY that gives the part number for the radiator sensor you'll need as well if you chose not to use a fan controller.

  • Thanks 1
PyroIndustries Contributor

PyroIndustries

Posted
  • Author
Posted
i dunno if this is the case with the skyline motors but in the old holden motors (253ci,308ci) disabling your engine fan and using thermos can increase hp (less drag, more efficiant)... slightly

anyway... are you putting one/them in front of your radiator? or infront of your engine?

infront of the engine

one 14" would fit nicely

PyroIndustries Contributor

PyroIndustries

Posted
  • Author
Posted
Dont install two small ones unless you use the EF/EL setup that comes with the shroud. Other than that a single 16" fits the factory shroud and will flow as much if not more than the factory crank fan.

Theres a DIY that gives the part number for the radiator sensor you'll need as well if you chose not to use a fan controller.

Sorry new here cant find DIY on it

chuckie Mentor

chuckie

Posted
Posted

In my R33 skyline the clutch in my fan has had it.

I was thinking instead of replacing the standard fan i should just throw in a thermo electric fan

was thinking one 14" fan

or should i have 2 smaller ones?

any advice would be nice

thanks

G`day all if you have a look at maxima with v6 front wheel drive look`s like they will drop in not much to do all gen part`s switches & all ?????,i will be putting these in my s2 stagea.if you all so look at tran`s cooler ,powersteering cooler if you need them ?????,good luck chuckie.

skybarge Community Regular

skybarge

Posted
Posted (edited)

I'm using a Craig Davies 16" drag racing fan flows 3800CFM with a 90C Degree thermoswitch

cost me $280 for the fan and switch

All mounted on a 55mm thick 180SX radiator with custom top pipe, works fine :) keeps the temps down, I even drove my car without the fan wired up, round 30 minutes and it never hit over 1/2 way on the temp chart :S

Oh and it does have a bit more go :) it's not dragging like it used to, but that's because I stripped the aircon as well i thinK :)

total gain from the fan would be in the area of round 5hp i think

Edited by skybarge
  • 2 weeks later...
W0rp3D Grand Master

W0rp3D

Posted
Posted
Other than that a single 16" fits the factory shroud and will flow as much if not more than the factory crank fan.

You might want to check into this a little more, i did the same conversion on my old rx7 and the cooling of the thermo was shyte (was a 16" davies craig) , would not do any where near as good as the clutch fan and have since heard many stories about many different cars that are driven hard and the thermo's dont work anywhere near as good as the factory clutch fan, i had my temp controller turned up full and if i drove normally or babied it it would sit at normal temp, as soon as i started to give it some it would shoot up, i would only need to do the equivalent of a 1/4 mile run and the temp would be up.

STATUS Grand Master

STATUS

Posted
Posted

the best solution is a FLEX-A-LITE dual system part number 220 these pull 2500cfm (davies craig seem to rate their fans way off!! as twin davies fans could not keep our car even remotely cool) the 220 keeps our drift car ice cold, i run a pivot fan controller but am working on a cheaper alternative.

The fans are the same size as the skyline radiator and have a rubber seal that seals against the rad surface.

110-210-Low-Profile.jpg

http://www.flex-a-lite.com/auto/html/low-p...e-electric.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...