Jump to content
SAU Community

Recommended Posts

hey guys is there a way to have your stereo turn off when you take the key out, cause my stereo stays on with the turbo timer intill the car shuts off. i was thinking of hooking up the ground wire to the factory ground wire insed of the chassie of the car

Link to comment
https://www.sau.com.au/forums/topic/181335-turbo-timer/
Share on other sites

undo the plastic panel under your steering column and look at your ignition barrel..one of the wires is for the accessories, use one of those red 'clip' inline joiners to attach and "bingo" job done!

Link to comment
https://www.sau.com.au/forums/topic/181335-turbo-timer/#findComment-3301739
Share on other sites

  • 2 weeks later...

what they meant is trace the trubo timer wiring loom down close the Ignition loom. Cut open the turbo timer loom common wire there is Red = constant 12V

Green or yellow = Ignition

Blue = go to 2nd Igniton or Accessory

* Cut the blue wire between turbo time and the Igniton loom and tape both end up woith electrical tape*

when ever your turbo timer is on the Blue wire will give out 12V+ from the timer to the Car Acc wire which turn on your head unit

Link to comment
https://www.sau.com.au/forums/topic/181335-turbo-timer/#findComment-3319434
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...