Jump to content
SAU Community

Recommended Posts

Hi guys,

got a 1997 Skyline gtst Series 2 front half cut (silver panels). Its automatic The half cut is the front chassis (With compliment plates), its complete however no radiator support as was cut and replaced on my car. Want to sell either complete or separate depending on convenience. Located in Sydney, NSW. The list below are the parts available:

* Front right guard- excellent condition with GT badge and indicator $200 (SOLD)

* Series 2 Front bar with foggies (not circle foggies n indicators) - no reo $400

* R33 Series 2 headlights (crystalised)- $600 (SOLD)

* R33 Series 2 steering wheel (no airbag) $120

* R33 Series 2 computer ECU and loom (Standard turbo) $150 (SOLD)

* Auto box external solenoid (i think thats whats it called) $250

* Dash cluster (Auto) with 80km - $100

* Busted airbag center steering wheel and motor - $50

* Busted passenger side airbag and motor - $70

* front fascier with clock, air con vents, antenna switch etc- good condition - $50

* passenger glove box - $30

* K&N filter and cover (good condition)- $50

* Plastic strip between bonnet and windscreen- $30

* set of fog lights from r33 series 2 (split and ok condition)- $80

* climate control unit $50 (SOLD)

* Ignition barrel $50 (SOLD)

* factory radio cassette $50

* Auto gear stick and all electrical components etc $100

* Entire bottom dash from steering wheel and below $100

* Factory fuse box in dash with all wires $30

* Factory fuse box in engine bay with all wires $50

* stereo DIN (SOLD)

PRICES NEGOTIABLE

Also got all electricals in dash like ignition, and all that belongs in dash...

post-35801-1193112602_thumb.jpg post-35801-1193112613_thumb.jpg post-35801-1193112590_thumb.jpg post-35801-1193112579_thumb.jpg post-35801-1193112568_thumb.jpg post-35801-1193112557_thumb.jpg post-35801-1193112544_thumb.jpg post-35801-1193112532_thumb.jpg post-35801-1193112517_thumb.jpg post-35801-1193112935_thumb.jpg post-35801-1193301766_thumb.jpg post-35801-1193301756_thumb.jpg post-35801-1193301745_thumb.jpg post-35801-1193301734_thumb.jpg post-35801-1193301716_thumb.jpg post-35801-1193822415_thumb.jpg post-35801-1193973429_thumb.jpg post-35801-1193973438_thumb.jpg post-35801-1193973448_thumb.jpg post-35801-1193973457_thumb.jpg post-35801-1193973467_thumb.jpg post-35801-1193973476_thumb.jpg post-35801-1193973487_thumb.jpg post-35801-1193973498_thumb.jpg

post-35801-1195124419_thumb.jpg post-35801-1195124440_thumb.jpg post-35801-1195124450_thumb.jpg post-35801-1195124460_thumb.jpg

All other electrical cables, headlight cables, carpets, dash components are scattered- just throw questions and offers.

Sydney buyers preferred but can deliver on buyers expense.

Leave a PM or email through the forum

post-35801-1193822426_thumb.jpg

post-35801-1193822435_thumb.jpg

post-35801-1193822445_thumb.jpg

Edited by johnabs
Link to comment
https://www.sau.com.au/forums/topic/181534-r33-series-2-front-halfcut/
Share on other sites

  • Replies 95
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...