Jump to content
SAU Community

Recommended Posts

Hey guys just wondering if i have a stock fuel pump in my gtr or not. I can hear it buzz loudly when i turn the car on (not start) for about 5-10 seconds. It's extremely noticable. Can you really hear the stock pump prepping? Thanks

Mine is quite loud as well. I think it is stock.

you are probably hearing the pump for the gearbox transfer case, that is a loud pump which turns on with ignition and goes for around 5-10 seconds.

The fuel pump will only do a 2-3 second prime on ignition to get pressure in the rail and can hardly hear it.

to make sure this is what you are hearing:

turn the ignition on

let the pumps do their thing until its stops pumping and no more noise

turn the ignition off

(and within 30 seconds i think it is?) then turn ignition back on

= the transfer case pump will not prime, but the fuel pump will.

^^ i hope that makes sense ^^ :P

Im pretty confident the fuel pump is the noisy one even when your talking about a stock item as mine does the same. Why would a transfer case pump be in operation at idle or with the ignition on only? They would only create pressure when you require front torque, thus locking up the clutch packs in the transfer case.

A better way to test which it actually is, is to remove the fuel pump fuse and switch the ignition on, make sure you havnt had the ignition on for quite awhile as mentioned so you would normally get the long prime noise.

Hey guys just wondering if i have a stock fuel pump in my gtr or not. I can hear it buzz loudly when i turn the car on (not start) for about 5-10 seconds. It's extremely noticable. Can you really hear the stock pump prepping? Thanks

I could hear mine; not _super_ loud though. The in-tank 044 I have now is only a shade if at all louder.

To tell if it's _really_ the fuel pump, pull the fuel-pump fuse and see if you still hear the noise

when you turn the key on.

Regards,

Saliya

Edited by saliya
Im pretty confident the fuel pump is the noisy one even when your talking about a stock item as mine does the same. Why would a transfer case pump be in operation at idle or with the ignition on only? They would only create pressure when you require front torque, thus locking up the clutch packs in the transfer case.

A better way to test which it actually is, is to remove the fuel pump fuse and switch the ignition on, make sure you havnt had the ignition on for quite awhile as mentioned so you would normally get the long prime noise.

sorry that's completely wrong. the loudest pump is the AWD pump. it primes when you switch the car on. there is an even easier way to test it. remove the AWD fuse, then turn ign on.

as for pump being standard or not, no one can tell you for sure just by the sound. sometime standard pumps get noisy. sometimes they are still quiet. sometimes aftermarket pumps are quiet, sometimes they are noisy. the only way to tell is pull it out and see what it is. or remove the fuel return and run it for a bit and see how much it puts out.

Fair enough. By the way, i didnt mean you could identify what pump you had by the noise i was just saying mine is stock and its noisy. I aggree with age they are likely to get louder. I also noticed my car does a quick prime if you leave the car idling for extended periods. Its the exact same noise that you hear when you first switch on the ignition but only for a real short time.

Can you explain to me how the transfer case works?

yeah, the second paragraph was not directed at you. just that it's impossible for us to tell what pump just because the guy says it's noisy when priming. if it's noisy when engine is running that may be another story.

as for the AWD pump priming at start up it's part of the systems check that happens when you turn a cars ign from off, to on. it checks sensors, abs circuits, primes fuel pump and primes AWD pump. and the AWD pump is by a long way the loudest. many a GTR owner have mistaken that noise for fuel pump noise.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...