Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Just wondering, wanting to start racing soon... so the helmet required... i read on Timeattack.com.au:

"Check that your helmet has the required safety stickers and has no cracks."

What safety stickers? Are there requirments like some "..... approved" helemt..

and... how about the long sleave to neck? is that forced?

"Check that your clothing is long sleeved, neck to wrist to ankle. "

Link to comment
https://www.sau.com.au/forums/topic/181994-helmets/page/2/#findComment-3335259
Share on other sites

You may want to edit the title of your thread or start a new one!

You need a helmet that meets the Australian Standards, one that has either ADR approval sticker or one with the Aussie tripple ticks...

Dont remove this sticker from your helmet once you buy it as it needs to be checked every time you race.

Good place to get a wide range of helmets is motorbike shops...

Thought for you tho;

When I bought my first helmet I asked "How much do i spend" cause the range is very wide from $50 through to thousands...

The salesman replyed with "How much do you think your heads worth" :)

Link to comment
https://www.sau.com.au/forums/topic/181994-helmets/page/2/#findComment-3335266
Share on other sites

lol typical salesman reply... :)

You'll likely find that the main difference between a helmet that costs a few hundred and one that costs $1200+ are things like air vents, snazzy colour schemes, racer endorsements and the like. You'll also pay more for removable linings (so you can wash or replace them as needed), clip-in guards that deflect your breath away from the visor, different kinds of visor pods, and of course the brand. HJC for example will always be cheaper than a Shoei or Arai. It depends just as much on what you're planning on doing with it as anything else.

All that said, if the helmet isn't comfortable and/or doesn't fit you properly, it's not safe. If you have a fat head like mine you'll probably want to look at a HJC, they're middle-of-the-road stuff in terms of features but just as safe as anything else. Remember that they all have to pass the same standards, but some pass by a much greater margin than others ;) All helmets sold here should be ADR approved to the best of my knowledge, but some will have other endorsements such as SNELL.

Link to comment
https://www.sau.com.au/forums/topic/181994-helmets/page/2/#findComment-3335390
Share on other sites

Hey,

Thanks for the info, just didn't want to start a new topic for something so small.... and thought someoen might have asked the question already. Trying to cover my ass :)

Well, regarding the helmets, so ADR approved is what i'm looking for.

I'm just in need of something that will protect my head, doesn't need to make me look good (colours, designs... etc). Air vents? Why do we need so many air vents? I don't think i need interchangable linen inside either :s!

Whats the rough price... for something that'll protect my head and is ADR approved.

Link to comment
https://www.sau.com.au/forums/topic/181994-helmets/page/2/#findComment-3335409
Share on other sites

Couple of hundred should do it easy. Get one that has a fibreglass outer shell rather than a plastic one, if you do smack your head into something the fibreglass will break off in sheets and will distribute the impact much more evenly, plastic will just bend/buckle around the point of impact. These days though it's pretty hard to buy a bad helmet though ;)

In regards to air vents and the like, unless you buy a helmet specifically for car racing, chances are it was designed with bike riders in mind. On a bike when a windscreen isn't stopping most of the air flow, air vents make a huge difference to your comfort level on a hot day, and removable liners are great for when you've sweated into them a heap and they start to get a bit smelly or greasy, or if after a few years the foam in them starts to break down or flatten. Just pull out the liner and either wash or replace it, viola, new helmet :)

Link to comment
https://www.sau.com.au/forums/topic/181994-helmets/page/2/#findComment-3335563
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...