Jump to content
SAU Community

Recommended Posts

You will find that your lights are crazed ( they have tiny little cracks on the lens from exposure to the sun) nothing short of changing them can fix it . Put your lights on at night and look in the lens you will the tiny little cracks . Polishing them fixes it for a little while, well makes them look better, not realy fixes them.

Mine are pretty bad on my R33, so i was going to replace them, but everywhere i inquire they all want anywhere from 350 to 450 per head light.

Is there anywhere I can get a set from that is not going to hurt my hip pocket to much. 700-900 for a pair of second hand oem headlights is a bit steep for me.....unless im cheap :D

I see some on US Ebay second hand ones that start low, but unsure if they will comply with AU standards?

Is it possible just to replace the headlight lenses wit new ones?? I know they're sealed on,

but are there places that heat off the old one and can fit a new one on? Can you buy just the lenses from nissan?

S2 Headlights new from nissan are $500+ each

Mine are pretty bad on my R33, so i was going to replace them, but everywhere i inquire they all want anywhere from 350 to 450 per head light.

Is there anywhere I can get a set from that is not going to hurt my hip pocket to much. 700-900 for a pair of second hand oem headlights is a bit steep for me.....unless im cheap :D

I see some on US Ebay second hand ones that start low, but unsure if they will comply with AU standards?

I have a good pair, no fogging and nothing broken you can have them for $350.

Get some really fine sandpaper, and some warm soapy water, and sand the headlights until you get a milky residue.

You can repeat again with a more corse paper, but still really fine.

Then cut and polish it with some good polish.

Has worked for me before, so give that a go.

Takes away the hazey yellow layer, and makes them pretty damn clear.

My xenons have gas marks on the inside of the lens, and from what i've heard the lights are totally sealed so apart from using a heat gun or something to open em up anyone else opened R34 len's ot cleaning the inside of them?

I use Meguires PlastX. It's a clear plastic polish specially designed for faded plastic and works pretty well. A few people i know thought i replaced the headlight. For $18 you cant really fault it except that you have to re-apply it every 1-2 months.

Edited by quiksta

lol 18 $$$$$$$$$$$$$

i just use 20 cents worth of polish and a bit of wax and it last for 2 months

has anyone else tried the wetrub with 1500 like mentioned earlier?

there is a new 29 $ dollar headlight kit i seen in supercheap but cant rem the company?

I know for the supras theres a mob that makes glass lenses for them. You can unseal the standard ones with a heat gun or oven or something, then replace the lens with a glass one and never worry about fading.

Any one made like a replacement glass lens for the skyline head lights instead of plastic??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...