Jump to content
SAU Community

Recommended Posts

  • Replies 187
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I*ts still fighting, Longest labor pains i ever saw. mick the magician is working through the bugs one by one.

Couldnt get it to rev past 4500 initially. Brand new plugs were cracked, one completely broke when we pulled it out.

Fixed that. got it running, dosed it to 5000 rpm and it went spastic, 30 lb of boost and mass power. WTF. Seems some clown hooked up the wastegate incorrectly. :P:no::P:( I think the cat did it. ;) Fixed that and started real time tuning. almost there with the run in tune. Had to turn it off because of the noise curfew. Still way rich, no timing, low boost at 6900 rpm making 296 hp atw.

Gonna finish the run in tune tomorrow morning. gotta love micks final shot before the night. "f**k this thing is gonna make some fat when we start power tuning" hmmmmm, Aint that what we built it for. :laughing-smiley-014:

whats low boost noel? fk me 30lb boost, wheelspin tyre smoke and flamage out the back end?? haha make sure you post that chart up noel or atleast shane n e way.

Low boost will be 18 lb for daily and 25 lb for hipo Adam. thats what it was built for and it will do it all day long unless i am mistaken. It has all the gear to do it and do it safely.

The engine has a good feel to it. I think its a winner. I am going to predict somewhere around the 375/380 rwkw on hi boost. :whistling:

I just blew, shit myself and em having the tantric moment atm.....

one word.

FARKENHELLIJUSTWANTONE!!!

Edited by Oblivion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...