Jump to content
SAU Community

Recommended Posts

yeh radiator.

no thats for a G35 auto. you can run an external trans into the loop with the in built trans. hence no need for a thermostat, as the radiator will warm up the oil and keep it at running temp a lot quicker than an isolated trans cooler.

im getting Race Radiators to make mine custome. 3 way pass, in built trans cooler. and holds about 2 litres more.

will be ditching the trans cooler if this one seems good enough.

How much for the custom job?

install it yourself. its not that hard

scott? :rolleyes: lol yeh will probably have too.

Even still, it's not a bad price if you don't want an external oil cooler.

Actually one of these might fit a bit tidier in the engine bay: http://www.makcotran...m/708-4739.html

yh it isnt. but a mishimoto one will cost you 400 delivered.

I couldn't find any with the trans sooler. They all said "Suit Auto" but then you'd ask them if they had the trans cooler and they'd say that they dont.

yeh i didnt go to the extent of pm'ing them so you may be right

theres nothing wrong with having the bottom tank cut and have the trans cooler loop installed in one that doesnt have it from the factory. any radiator place should be able to do it

this is true, but for the total cost of getting theradiator, plus a tank installed you may aswell get a custom one.

if you guys are interested in radiators from RaceRadiators, I can get them to keep the design when they do mine? perhaps they'll deliver.

Yeah I'm interested in the Race Radiators thing, keep us posted. $700 isn't bad if the Koyo is going to cost Jase $600.

That said I'll probably still run past Tonkins and see what they say though.

Yeah I'm interested in the Race Radiators thing, keep us posted. $700 isn't bad if the Koyo is going to cost Jase $600.

That said I'll probably still run past Tonkins and see what they say though.

when cam comes on he'll be able to tell you all about it. he already has one!

What about running a small cooler such as:

http://www.ebay.com....=item3cbaf1095d

or

http://www.ebay.com....=item19b30e6035

and just plumbing it before the radiator as previously suggested?

What size cooler are you guys running and where do you put it?

im running a PWR one for a Ford V8. imo those coolers are too small' and to be honest, i dont think the fluid will spend enough time in the cooler to physically cool.

im running a PWR one for a Ford V8. imo those coolers are too small' and to be honest, i dont think the fluid will spend enough time in the cooler to physically cool.

Do you have a link? Where did you mount yours Aaron?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...