Jump to content
SAU Community

Recommended Posts

hey Clint32 did you notice much difference goin from 4:3:1 to 4:1:1?, I read on www.calaisturbo.com that its's worth dropping in 4:3:1 that the r32 gts-t has combined with the engine/gearbox conversion to get the most out of the conversion, my only problem with the conversion is that the speedo is about 20km/h out!

Link to comment
https://www.sau.com.au/forums/topic/18561-diff-ratios-r32/#findComment-412514
Share on other sites

  • 8 months later...

4.3 = 3700-3800 in 5th at 110km or around 3500 at 100km/h in 5th. mite sound like a bit. put your foot down and your on boost in around.0000000003 seconds :P lol.. so its alright for taking over slower moving cars.. or when you want to race your mate in 5th gear.. lol. but yea.. your looking at higher revs for any given speed in any given gear.. remember that. but i like my 4.3's

Link to comment
https://www.sau.com.au/forums/topic/18561-diff-ratios-r32/#findComment-714664
Share on other sites

  • 3 months later...

I just had my diff pulled down and it had 4.11 ratio from what I was told.(92 R32 GTS-T)

While I'm at it does anyone know where I can get a new crown wheel and pinion gear set (4.11) for an R32 GTS-T?

I ask as the old crown wheel is marked and I decided to not change it (to save $$$)but it still wines a fair bit so if I can get a new gear set it would be nice.

Link to comment
https://www.sau.com.au/forums/topic/18561-diff-ratios-r32/#findComment-898671
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...