Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm after a bit of advice, I have an r32 gts-t (93), I have noticed my factory oil pressure guage reads quite low (nearly back to 0 on idle, and only just above 2 for normal driving), is this likely to be an oil press sender issue? It runs fine, plenty of oil etc...

Also another quick question, I occasionally get a small hesitation when I roll off and back on the throttle, as in, I back off slightly, and then when I squeeze the pedal back on it gives a small miss, and then pulls away fine, not the end of the world, but it never used to do it.

Any help would be great!

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/186241-r32-oil-pressure/
Share on other sites

Hi guys,

I'm after a bit of advice, I have an r32 gts-t (93), I have noticed my factory oil pressure guage reads quite low (nearly back to 0 on idle, and only just above 2 for normal driving), is this likely to be an oil press sender issue? It runs fine, plenty of oil etc...

Also another quick question, I occasionally get a small hesitation when I roll off and back on the throttle, as in, I back off slightly, and then when I squeeze the pedal back on it gives a small miss, and then pulls away fine, not the end of the world, but it never used to do it.

Any help would be great!

Cheers.

Oil pressure Sender units are notorious for giving up the ghost, have someone check your oil pressure with a mechanical gauge. Flat spots are generally caused by a lean mixture, you may have an air leak into the inlet manifold.

  • 2 weeks later...
...I have noticed my factory oil pressure guage reads quite low (nearly back to 0 on idle, and only just above 2 for normal driving),

I notice the exact same thing with mine, could it be normal for a R32 GTS-T. My oil pressure does however rise to 4 after it has fully warmed up though.

My motors healthy (compression tested etc..) but the oil pressure gauge always reads low.

On start up when cold it will be just under '4' on the stock oil pressure gauge, and it only gets lower as it gets warmer.

When cruising at a consistant speed its quiet low, but at about 100km/3XXXrpm its in between '2' & '4'..

I don't really worry about it to much as I have been told the stock oil pressure gauge is useless, so I won't be able to get an accurate reading till I get a decent after-market oil pressure gauge.

i also notice the guage gets lazy around oil change time(5000kms)

Yeah mine went heaps low after I serviced it.

Was slightly worried with it being so low..

Edited by abu

Hi again all,

Well I have fixed the problem, turned out to be an interesting one!

I had just replaced oil and filter before I started having this problem, and I used penzoil 10w30, which was a mineral oil, and as I read some of the posts is not the stuff to use, so I went to supercheap and got some fuchs 10w30 synthetic and chucked that in just to be safe.

Took her for a drive, and to my surprise, oil pressure is now back to normal readings on the guage! Not sure how that works being the same viscosity of oil and all, but thats how it hapened!

Cheers,

Rosco.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...