Jump to content
SAU Community

Turbo Falure

Viper_r32

By Viper_r32,
in Australian Capital Territory

 Share

Recommended Posts

Viper_r32 Community Regular

Viper_r32

Posted
  • Author
Posted

yippee, my ride is finally back on the road!. i went and picked her up yesterday from integra and anthony showed me the official report from GCG with photos and all. I'll post some pics up later when i get a chace to scan them. but after looking at the pics and discussing with anthony how this could have happened we came to the conclusion that i haven't had my turbo timer set for long enough. i was an aware that ball bearing turbos require longer to cool down than leaf turbos and 2 mins of turbo timer is just not enough after a hard drive. so after all that it turned out it was my fault for the turbo dieing, apparently i should be letting the turbo run down for at leaset 5 min, i only wish they could have at least given me that info when i had it high flowed in the first place. you would think it would be critical information that a customer should be given. but any way she's back on the road and I'm slowly working the turbo in on stock boost for a while. and very happy to finally have my car back :ninja::P

Michele Veteran

Michele

Posted
Posted

Mines stock, so can someone tell me how long I should have my timer set for after a normal street drive (nice'n'easy one that is)? If I'm only putting around, I have only been giving it about a minute or two.

MIVEC Mentor

MIVEC

Posted
Posted

There are many varying opinions on how long a car should be left on to let the turbo cool down.

Personally I never really leave it for any longer than 30 seconds unless it's been a hard drive and I've not done a 'cool down lap' on the way to my destination.

Al Grand Master

Al

Posted
Posted

Well if these turbo shops are claiming "oil contamination" as the cause of failure, i would personally send a sample of the oil to be tested. Funny how the standard turbo lasted 15yrs, with the oil passing through the same lines and i'd bet "oil contamination" wasn't the reason why it failed :worship:.

Once the oil has been tested and if the results show no metal rust contamination, then i would hit the company for replacement turbo, test and fitting costs.

Al Grand Master

Al

Posted
Posted
yippee, my ride is finally back on the road!. i went and picked her up yesterday from integra and anthony showed me the official report from GCG with photos and all. I'll post some pics up later when i get a chace to scan them. but after looking at the pics and discussing with anthony how this could have happened we came to the conclusion that i haven't had my turbo timer set for long enough. i was an aware that ball bearing turbos require longer to cool down than leaf turbos and 2 mins of turbo timer is just not enough after a hard drive. so after all that it turned out it was my fault for the turbo dieing, apparently i should be letting the turbo run down for at leaset 5 min, i only wish they could have at least given me that info when i had it high flowed in the first place. you would think it would be critical information that a customer should be given. but any way she's back on the road and I'm slowly working the turbo in on stock boost for a while. and very happy to finally have my car back :worship::(

Sorry to say that sounds like complete BULLSHIT.

Unless you are thrashing the car to the driveway, smoking the tyres till you park, 2 mins of turbo timer is MORE than enough. Hell if you drive normally for the last few minutes of your trip, then 30secs is enough. My turbo timer is set to 20sec, and unless i am competing in a motorsport event, i never increase the time and my HKS turbo has never had a problem.

The only other reason of failure, is that the turbo wasn't primed/lubed before starting the engine for the first time, thus causing the bearing to heat up and score, during the initial few seconds

Back to the turbo:

How long did it take till you delivered the turbo, to the time you received the report.

Not saying this has happened, but can you be sure those pics are from your turbo?

Not saying that the company involved is responsible, it could have been an installation issue (refer above about primming), but the turbo company has specified oil contamination, so get the oil tested.

race_snooze Grand Master

race_snooze

Posted
Posted
as far as i know around 2 to 2 and half minuets for the stock turbo should be fine, as it is not ball bearing

Actually they are Ball Bearing and BB need less time then Bush bearing to cool down and are more tolerant to quick heat and cool then bush.

Some correct me if I am wrong...

dmr Mentor

dmr

Posted
Posted
yippee, my ride is finally back on the road!. i went and picked her up yesterday from integra and anthony showed me the official report from GCG with photos and all. I'll post some pics up later when i get a chace to scan them. but after looking at the pics and discussing with anthony how this could have happened we came to the conclusion that i haven't had my turbo timer set for long enough. i was an aware that ball bearing turbos require longer to cool down than leaf turbos and 2 mins of turbo timer is just not enough after a hard drive. so after all that it turned out it was my fault for the turbo dieing, apparently i should be letting the turbo run down for at leaset 5 min, i only wish they could have at least given me that info when i had it high flowed in the first place. you would think it would be critical information that a customer should be given. but any way she's back on the road and I'm slowly working the turbo in on stock boost for a while. and very happy to finally have my car back :P:)

wow smells like bullshit. looks like they're trying to give excuses now.

like Al says, i think it's only really mandatory to run your turbo timer for 2 minutes if you've been bashing the limiter all the way home. i'd be going back for complaints.

Scooby Veteran

Scooby

Posted
Posted (edited)

drive normally for 5 minutes after a thrash, and with a bb water cooled turbo it's doubtful you'll need to cool down more anyway.

and if you haven't thrashed it then normal shut down without a cool down is fine ie manoeuvering into the garage after cruising down the street is enough.

Edited by Scooby
Viper_r32 Community Regular

Viper_r32

Posted
  • Author
Posted
Sorry to say that sounds like complete BULLSHIT.

Unless you are thrashing the car to the driveway, smoking the tyres till you park, 2 mins of turbo timer is MORE than enough. Hell if you drive normally for the last few minutes of your trip, then 30secs is enough. My turbo timer is set to 20sec, and unless i am competing in a motorsport event, i never increase the time and my HKS turbo has never had a problem.

The only other reason of failure, is that the turbo wasn't primed/lubed before starting the engine for the first time, thus causing the bearing to heat up and score, during the initial few seconds

Back to the turbo:

How long did it take till you delivered the turbo, to the time you received the report.

Not saying this has happened, but can you be sure those pics are from your turbo?

Not saying that the company involved is responsible, it could have been an installation issue (refer above about primming), but the turbo company has specified oil contamination, so get the oil tested.

sorry i've been away for a while working on a feature film being filmed in goulbourne. now that you metion it one thing i found realy fishy is the photos taken of my turbo have a date stamp of early 2004.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...