Jump to content
SAU Community

Fs - R33 Gtr Turbos And Rb26 Short Block

[200]
 Share

Recommended Posts

[200] Mentor

[200]

Posted
Posted (edited)

I have for sale a twin turbo setup from a stock R33 GTR motor that travelled 56,500kms. There is no shaft play what so ever in the turbos and they seem to be in good condition.

turbo01.jpg

turbo02.jpg

turbo03.jpg

turbo04.jpg

turbo05.jpg

turbo06.jpg

$500 ono

Located in North Sydney.

Pick up only unless you organise freight and cover costs.

Edited by [200]
Beer Baron Grand Master

Beer Baron

Posted
Posted

why was the motor disasembled? and I'm assuming it is all complete with:

crank

rods

girdle

pistons + rings

oil and water pump

was it in running condition when head was taken off?

[200] Mentor

[200]

Posted
  • Author
Posted (edited)

Thread updated with better pics of the turbos.

NB re postage

Turbos will be sent in 2 boxes. Dimension are,

42cm long

22cm high

20cm wide

7.2kg weight

Remember there are 2 boxes.

Lodegement post code is 2065. For those interested you can caluclate the postage costs with the online Australia Post calculator

Australia Post

Edited by [200]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...