Jump to content
SAU Community

Recommended Posts

Dang carl, i got a momo you can buy cheap

cheers Steve, i'll give ya a holler after payday :(

Dam bezender that's crappy as.. :)

Where do you live?

im in south brighton, my street is fair busy, and the front door is well visible from the road... not a huge surprise when u think about it like that... gonna go for registered mail from now on with ebay, that way they cant just drop the package n run

dammit, just got turned down from a job that i was looking forward to getting in a different IT company. also a MOMO steering wheel thing for the PC that i bought off ebay was stolen from my front porch when it was delivered!

aus post FTL... sif they dont ring the doorbell or knock, i was sitting right there in the front room :yes:

I buy a shit load of r/c parts and car parts from ebay and after i got one part stolen from my frount door i got a PO box only $70 a year, its well worth it

cheers Steve, i'll give ya a holler after payday :P

im in south brighton, my street is fair busy, and the front door is well visible from the road... not a huge surprise when u think about it like that... gonna go for registered mail from now on with ebay, that way they cant just drop the package n run

Yeah registered mail is the way to go.. hope the part wasnt to expensive

I buy a shit load of r/c parts and car parts from ebay and after i got one part stolen from my frount door i got a PO box only $70 a year, its well worth it

Would most of the parts fit in the box? :yes:

Rather than start a new thread, my uncle dropped the bleeder nut when flushing my radiator and it fell down into oblivion, any nuts in the engine bay you can transplant for it? Devo that it had to get lost on a friday night! No car ftl T_T

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...