Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

writeoff Mentor

writeoff

Posted
Posted (edited)
:( Woo Hoo! :P

Anyone guess why I'm so happy?

You just found out that you will lead the first float in this year's Gay & Lesbian Mardi Gras parade?

Edited by writeoff
Hotwire Veteran

Hotwire

Posted
Posted

^speaking of that, anyone watch Good News Week last night? I though it was funny what they said about Sydney taking the Grand Prix from melbourne and running it at the same time as Madi Gras..... "hook the floats up to the F1 cars and get the poofs outa there quicker"

LOL

or something to that effect

*flick* Veteran

*flick*

Posted
Posted

Lucky u nick

I 'politely' told my managers where to stick my job - well current position today, stepped down from being manager, but wouldnt sign anything for a few weeks since i got holidays after next week.. and stepping down = less pay, so may aswell take my holidays on the manager rates and get as much as i can out of them :)

Whiplash Grand Master

Whiplash

Posted
Posted

have / had a few things lined up, i think i missed out at the job at BMW they were going to let me know yesterday if i got it and no phone call :)

might have a week off before i start looking seriously (what a shame the clipsal is in that week)

Luke_ENR34 Grand Master

Luke_ENR34

Posted
Posted

was either to toyo proxes 4 or some other toyo's troy (Adelaide tyre power) was telling me about.

Around 300 a tyre + guard rolling ($50 a guard)+ wheel alignment (think around 60) not cheap.

will post pics later today.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...