Jump to content
SAU Community

Recommended Posts

I just hade a spestic moment, i was sitting on my pc chair and the leg snaped and i was left on the ground but i couldnt stop laughing

So now im thinking i got problems :blink:

Ha, Ha....were you doin the big recline thingy?......I've snapped a couple of office chairs in the last 12 months in the same way.....I reckon its because they're cheap junk

Ha, Ha....were you doin the big recline thingy?......I've snapped a couple of office chairs in the last 12 months in the same way.....I reckon its because they're cheap junk

lol yap i was all the way back then i was on the floor

so does anyone know why there were like 50 cop cars heading down marion/ south rd today around the airport?

reckon star force were there to. must of been something serious.

they were a day late.... I flew back in friday night. :blink:

BTW, Im with Bigpoond, havn't had a problem with SAU all weekend.

good point

oi, how much shaft play (if any) should my turbo have...............................

Ball bearing..... 5 fifths of f**k all really. Plain journal bearing.... a small amount is acceptable in my eyes...

Got a bit? Where's the play? side to side or lengthways through the turbo? (comp cover to exh. housing)

Hopefully have my new turbo on in a week or two mate. We'll chuck that 25 turbo on ASAP if you think it's a problem.

Edited by R31 drift pig
Ball bearing..... 5 fifths of f**k all really. Plain journal bearing.... a small amount is acceptable in my eyes...

Got a bit? Where's the play? side to side or lengthways through the turbo? (comp cover to exh. housing)

Hopefully have my new turbo on in a week or two mate. We'll chuck that 25 turbo on ASAP if you think it's a problem.

swapped dump pipes with chris yesterday, mine's still off. had a jiggle (front to rear) with the exhaust wheel and it seems to have a mm or two movement. so lengthways. hasnt been blowin smoke or any shit like that, plus i only gotta run next weekend before i go away to shepparton. See how i go

so does anyone know why there were like 50 cop cars heading down marion/ south rd today around the airport?

reckon star force were there to. must of been something serious.

3 bikies. arrested at the airport. Pathetic really

This is what we get from mike rann, cos hes so uber hardcore tough on bikies n shit...

stupidity

-D

3 bikies. arrested at the airport. Pathetic really

This is what we get from mike rann, cos hes so uber hardcore tough on bikies n shit...

stupidity

-D

These new anti afilliation laws will be interesting as far as enforcing them. I haven't read the fine print yet but I did get pulled over by avatar near Darlington recently to see if & who I was associated with. I'm wondering whether dealing with an outlaw biker through his legitimate bike business for parts etc is allowed? Or whether socializing with clubs that aren't necessarily branded as outlaw clubs like the Long Riders, Vietnam Vets, Ulysses & CMA (Christian Motorcycles Association) will be tolerated?

My mate & I have been invited to one of their clubrooms next Friday night & we're actually contemplating it, moreso out of curiosity.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...