Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

Jack88 Experienced

Jack88

Posted
Posted

iv had it with the weather now! i washed my car before and not one drop of rain while i was washing it,i just finished shamying the entire car and was about to put it under the carport when it just randomly poored with rain and soked the car again!! :banana:

rhys5169 Mentor

rhys5169

Posted
Posted
Im tired, been at autosalon all day kicking rude people off our display, can't you see that it's roped off? geez. the graham west dyno has low balled everyone, mine only made 165rwkw :banana:
bout time those autosalon dyno's were realistic.

bahahahahahhaa

Min_R32 Proficient

Min_R32

Posted
Posted

Hey guys, i need to find these four connections on my ECU. Ive never touched the wiring on my ECU before and just wanted to make sure that i have the right wires.

I need:

+12V Ignition Switched pin

Ground Chassis 0V

Oxygen Sensor signal

Airflow Meter signal

Now ive found this ecu diagram pinout

RB20_ECU_Pinouts.jpg

Now im pretty sure that for the 12v ignition switched im looking at pin 45, and for Ground 0V im looking at pin 10 or pin 20. (Please correct me if im wrong)

Airflow meter signal is pin 27.

Im not sure where the other pin for oxygen sensor is. I found another ecu diagram with the oxygen sensor on it (Pin 55) but im not sure as the diagram above says 55 is nothing =/ I know how to check these with a multimeter but i just wanna make sure first =)

D_Stirls Veteran

D_Stirls

Posted
Posted (edited)
Im tired, been at autosalon all day kicking rude people off our display, can't you see that it's roped off? geez. the graham west dyno has low balled everyone, mine only made 165rwkw :)

It's Mainline Dyno's are more accurate to real HP than the dynodynamics ones. Everyone is in the same boat though and it also makes "SLO 33"s 465kw more impressive, It would be more like 510kw on a DD dyno.

Edited by D_Stirls
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      This car has run before on this z32 ecu can get the part number for you, I have tried with no AFM it didn’t change anything, I compression tested today 140-150 across all 6 cylinders, also set fuel pressure to 43psi. The only weird thing was cylinder 1 plug was black and fouled other 5 cylinders were just wet with fuel. Spun cas by hand and confirmed injectors are clicking 
    • MBS206
      new 1.5 LSD issues/concerns

      By MBS206 · Posted

      Since you came here to ask for help, have you thought about answering our questions, that might help us lead you to why it was skipping, or have you given up on getting advice?
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
×
×
  • Create New...