Jump to content
SAU Community

Recommended Posts

iv had it with the weather now! i washed my car before and not one drop of rain while i was washing it,i just finished shamying the entire car and was about to put it under the carport when it just randomly poored with rain and soked the car again!! :banana:

Im tired, been at autosalon all day kicking rude people off our display, can't you see that it's roped off? geez. the graham west dyno has low balled everyone, mine only made 165rwkw :banana:
bout time those autosalon dyno's were realistic.

bahahahahahhaa

Hey guys, i need to find these four connections on my ECU. Ive never touched the wiring on my ECU before and just wanted to make sure that i have the right wires.

I need:

+12V Ignition Switched pin

Ground Chassis 0V

Oxygen Sensor signal

Airflow Meter signal

Now ive found this ecu diagram pinout

RB20_ECU_Pinouts.jpg

Now im pretty sure that for the 12v ignition switched im looking at pin 45, and for Ground 0V im looking at pin 10 or pin 20. (Please correct me if im wrong)

Airflow meter signal is pin 27.

Im not sure where the other pin for oxygen sensor is. I found another ecu diagram with the oxygen sensor on it (Pin 55) but im not sure as the diagram above says 55 is nothing =/ I know how to check these with a multimeter but i just wanna make sure first =)

Im tired, been at autosalon all day kicking rude people off our display, can't you see that it's roped off? geez. the graham west dyno has low balled everyone, mine only made 165rwkw :)

It's Mainline Dyno's are more accurate to real HP than the dynodynamics ones. Everyone is in the same boat though and it also makes "SLO 33"s 465kw more impressive, It would be more like 510kw on a DD dyno.

Edited by D_Stirls
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...