Jump to content
SAU Community

Recommended Posts

probably Steve.

Ok, so i have bought a Power FC, no hand controller. Should i get a HC before i worry about installation and tune?

Just got my HID kit, which looks (to me) like the connection from my globes to my HID kit dont match. Anyone wanna fit it for me, or know of someone who will do it? Im thinking Auto Perfection.

Cheers guys.

probably Steve.

Ok, so i have bought a Power FC, no hand controller. Should i get a HC before i worry about installation and tune?

Just got my HID kit, which looks (to me) like the connection from my globes to my HID kit dont match. Anyone wanna fit it for me, or know of someone who will do it? Im thinking Auto Perfection.

Cheers guys.

got some pics of it there damo?

i can fit them but its abit of a drive for you tho :)

hey guys, I've been away from my computer for about 4 hrs and just got back to see the mods have removed the thread about "Photos" from that dude with the bi-polar disorder.

Did he end up flaming me for saying that manic depressants shouldn't be off their medication?

I don't know if I should've been laughing or feeling sorry for the poor buggar.

so craig, in a nutshell, what what else was said after my post to that dude?

I was hoping to found out what his deal was beofre the thread was actually deleted.........he obviously came across as a hacker with a few personal issues!

lol, pretty much nothing ha ha, no replys from him, at all.

just more people adding to the confusion of the whole thread.

oh, and charmaine handed out some '' verbal bashing'' to a few randoms lol

I see the "SA Photo" thread is gone too.

Chris is an ok bloke, but has had some issues in the past - guess you could say he is a rather misunderstood kind of guy. Its not my place to talk about his past, but just remember he is a nice bloke who's had some issues. I'm sure everyone on here has had their good/bad days, and today probably wasn't one of his better with regards to agreeing with forum rules.

I never saw you post Pete - you have PM

But for all benefit - Don't feel sorry, but don't give him a hard time either. He is a Nice guy, and always up for an interesting chat if you give him the time of day rather than being an e-warior like many of you are.

LOL my "verbal bashing" was quite well deserved.

The bastard hijacked my personal photography thread in the photography section on SAU. And randomly posted HIS photos in MY thread...for MY photos only.

Im in a mood atm, where if he did it again i would be hell like :D:):(:domokun::domokun::domokun::domokun:

I think you get my point :angry:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...