Jump to content
SAU Community

Recommended Posts

woot on tuesday night the cooler and turbo are getting bolted up to the car! new oil going in and coolant, clutch fluid and all others :(

also gonna be making up a xmember extension and mount the gearbox! then send the tailshaft off :(

GAME ON

woot on tuesday night the cooler and turbo are getting bolted up to the car! new oil going in and coolant, clutch fluid and all others :(

also gonna be making up a xmember extension and mount the gearbox! then send the tailshaft off :(

GAME ON

about BLOODY TIME...LOL it better be finished by the time i get back from overseas

What a day of news, an Aussie wins the Indie, Adelaide United goes to the top of the A league table, and a family is suing for being served shit in their sundae :(

Edited by Damo_R34
when u going and were?

leaving nov 3rd and coming back nov 30th

going to Bangkok then Cang Mae then Vietnam then Phukett then Back to Bangkok 4 the last week

looking forward to getting a "HAPPY ENDING" :( ...ROFL

so thats plenty time 4 u Adrian 2 get it finished!!!!!!!!

erm that easy you noob make a fan

also CORRECTION no standard piece of paper can be folder more than 7 times IN HALVES

Err, ok, you just corrected it yourself, im sure everyone else knew what i was on about

this will keep the kids entertained, no standard piece of paper can be folder more than 7 times

erm that easy you noob make a fan

correct..........it's never been done by hand......feel free to start with a massive piece of paper

myth busters already tried that

also CORRECTION no standard piece of paper can be folder more than 7 times IN HALVES

>>Seven Folds<<

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...