Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

Tangles Grand Master

Tangles

Posted
Posted
Errr Brendan - you do realise it is a GTR with around 450rwkw and has run low 10's? You would have kept within sight range for around 30 seconds, and would have been it :D

umm yer, you reckon I couldnt keep up in the twisties, being an ex-bike rider whos used to lines and 220+kmph corners?

lol, as said, $50 is a bet id take :laugh:

all in good fun

Ryan&Sez Collaborator

Ryan&Sez

Posted
Posted (edited)

Im bored too... i hate exam time. One down today (animal health) got three to go.. sigh. I have business management for applied science saturday morning.. yes thats right an exam on SATURDAY MORNING! Adelaide uni is so mean :laugh: Can't wait until it's all over!!

Sez

Edited by Ryan&Sez
Boof Mentor

Boof

Posted
Posted
Im bored too... i hate exam time. One down today (animal health) got three to go.. sigh. I have business management for applied science saturday morning.. yes thats right an exam on SATURDAY MORNING! Adelaide uni is so mean :) Can't wait until it's all over!!

Sez

Far out thats just tired me out reading all that and i don't have to do any of them!!!

Ryan&Sez Collaborator

Ryan&Sez

Posted
Posted (edited)

my other exams are animan nutrition and animal behaviour, welfare and ethics - that's the one that puts you to sleep!! I'm so glad that this is my last full time semester :)

Sez

Edited by Ryan&Sez
Madaz Grand Master

Madaz

Posted
Posted
I can't believe it either.........I doubt if the block alone is worth $30K........maybe with very expensive internals ie. a short motor
Errr Brendan - you do realise it is a GTR with around 450rwkw and has run low 10's? You would have kept within sight range for around 30 seconds, and would have been it :)

You had better believe it mate .... BLOCK only. Definitely nothing else included. The crank that Munro is using was a cool $5k on top, then pistons and all the crazy gear incl. 1,600cc injectors - yes you read right. This is how he has spent $180,000 on the car. And yes, he has receipts.

Ring Keir Wilson right now and ask him - he has bought around 5 of the OS blocks all up due to blowing motors etc .... his wallet knows EXACTLY how much they cost .... I am not sure what exchange rate they were purchased at, but I am sure it was better than it is now too .... only recently he pointed out to me one sitting under his work bench at Willalls looking all lonely - I told him I would happily give it a home :) .... but as it isn't quite in my price range there it stayed :)

i found this 1,627,500.00 JPY (Japan Yen) = 26,404.34 AUD (Australia Dollars)

rb315kit.jpg

>>source>>

RB30 OS-E2996

Developed for those special customers who feel that 2.6 liters is just not enough.

OS Giken RB30kit contents

RB30 OS-E2996

- 1 cyclinder block

- 1 billet crankshaft

- 6 billet-forged connecting rods

- 7 crankshaft main bearings

- 6 connecting rod bearings

- 6 forged aluminum pistons

- 1.3mm metal gasket (1.2mm, 1.4mm and 1.5mm

gaskets available)

- 1 timiing belt

- 1 belt tensioner kit

- 14 custom made reinforced crank cap stud bolts and

nuts

- 3 M6 bolts

os_rb30_kit.jpg

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • Kinkstaah
      My BMW 335i

      By Kinkstaah · Posted

      I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      D2 and Ksport are essentially the same thing and basically just generic Taiwanese manufacture. Better than ChinaBay crap, but... not top shelf. Öhlins have got to be some of the best dampers around, so likely to be a good option. It's going to get to the point though where I suggest you buy from Oz. We have at least 2x excellent options here. If I were you though, I'd be talking to KW about doing something for the R33. There's bugger all difference between that and the 32. In GTR land, anyway.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      KW only offers a set for the R32 GTR. Popular options are D2 racing, Ksport or Öhlins. I have a D2 Racing coilover set, though I don't know for sure which one.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Well, the good news is you have more than one very good option for new coilovers in and around your country. Worth the drive over to KW to talk about GTR stuff.
×
×
  • Create New...