Jump to content
SAU Community

Recommended Posts

Plug in 66% as you had previously or slightly less. Might be worth going a little leaner with 60%.

When cranking go full throttle.

It probably won't start because the plugs are wet fouled then its just a big vicious circle. :S

i tried that the other day to no avail.

Adrian, we need to pull the plugs out,start again..I'll get it going after the job interview.

Edited by Ryanrb25

well.........

the car seems to be running on 4cyl with the new injectors in.. so out the injectors come and off for a flow test... hope two arent f**ked...

oh well we will wait and c how it goes... its all a learning curve!

Checked the injectors are receiving power with a multimeter?

The injectors always receive volts so simply turn the ignition to the on position and check with a multimeter.

The ecu earths the injectors to trigger them so obviously shove the neg of the multimeter on the chassis/battery.

Runs on 4.. Are you sure the plugs just arn't fouled.. Thats what a mate of mines did for a while we warmed it up, raised rev's and she cleared up. :huh:

Not in the mood.. Go and have a bat. lol.

Run it for a good 5mins or so with rev's slightly up.

Make sure the injector correct is set right so go with 'slightly' lean at 65%

.... It could be running for the weekend ...

Another way to check the injectors are firing and when they 'should' be firing is to pull the cas out; ignition to the on position and then spin the cas clockwise slowly when looking at the shaft from behind. You'll hear the injectors click click click. Make sure they follow the firing order. :unsure:

[Vent]

Put turbos back on, sell car?

Pay for removal/reinstallation and just take it in the nuts?

Sell engine, buy R34N1 engine + turbos and apply for an engine conversion?

In SA, that actually seems like a good idea....ARGHHH.

[/vent]

Another way to check the injectors are firing and when they 'should' be firing is to pull the cas out; ignition to the on position and then spin the cas clockwise slowly when looking at the shaft from behind. You'll hear the injectors click click click. Make sure they follow the firing order. :unsure:

yeh ive done that before but not with the new injectors.. ill give that a crack later..

if there not firing wats the go? there rooted?

[Vent]

Put turbos back on, sell car?

Pay for removal/reinstallation and just take it in the nuts?

Sell engine, buy R34N1 engine + turbos and apply for an engine conversion?

In SA, that actually seems like a good idea....ARGHHH.

[/vent]

how much for the n1's? my car needs a chrissy present

yeh ive done that before but not with the new injectors.. ill give that a crack later..

if there not firing wats the go? there rooted?

If there not firing its multimeter time to see if the problem is with the loom or the injector.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...