Jump to content
SAU Community

Recommended Posts

Half cage is legal. I'll get the section from the ADR handbook in a sec.

From memory, it must be padded and you must re-register your car as a 2 seater, but I'll look it up now.

Edit: and get it engineered, and carry the paperwork with you. But either way, cops wont have a clue and will defect you even if you show the engineers report.

Edited by CRoNic...
can anyone recommend anygood places to get roll cages made up that are road legal, cauz i wanna get a drift car biult up, and still have it legal for the road.

cheers... michael p.s guess its gunna be an expensive sport but, seems like poeple are getting into it, oww luke(orgzmc) do you know much places to get good parts and what i need for it, im thinking of a 180 or such.

Alright here's a quote from what the act says:

Roll Cages

Due to the increased risk of occupant injury in vehicle accidents the fitting of full roll cages are not permitted.

However, the fitting of a roll cage rearward of the driver is permissible providing that:

a. No part of the roll cage is contactable by vehicle occupants when positioned in their normal seating

position.

b. The roll cage is at least 150 millimetres rearward of the front seat occupants when the front seats are

located in the most rearward adjusted position.

c. All rear seats and seat belt assemblies fitted in the rear compartment are removed.

d. The operation and effectiveness of the front seat belt assemblies is not affected in any way by the roll

cage.

e. That no person travels in the rear of the vehicle at any time.

-dstroy u plan when and when you not gonna need it :D i think i might go roll my car

on a unrelated matter the 1 benefit of police attention on cars is i can skate freely where eva the hell i want, gone are the days i used to get 30 min leatures of pointless dribble and friends getting $50 fines. was skating down jetty rd went past a cop with time on his hands and nope didnt even so much as look at me. love it ;)

here is my stealth ute shes a monster now with the black sunnies and truck pipes, wonder how long till the cops pull me over bout it. :P

keep a look out for this at glandambo 4x4 event if anyone here goes to it you might see me there this year. im gunna jump the table top and land in the mudpit, hopefully land on all fours.

on another note is it illegal to have your cam gear cover off as i want to get some purdy red cam gears.

post-49670-1230989305_thumb.jpg

Not sure if it's illegal but I wouldn't recommend running no cover, if a stone gets kicked up from the road and comes into contact with the timing belt and causes trouble, things could get interesting. Just buy a clear cam cover then you have protection and can still see all the pretty stuff

hey all, just wondering if anyone knew if you can put gtr injectors into a 33 gtst and if so what els do u need? eg resistor packs

i do believe its a no go... they only fit on rb30 an 20 from wot i'm told...

rb25det are side fed, rb25det neo is top fed and rb26, rb20 are top fed

it could be done but there needs to be some modifications to the rail, collars etc best bet is to just go with side fed sards or nismo injectors

http://www.news.com.au/adelaidenow/story/0...5018092,00.html

For everyone who hates the human colostomy bag known as Amber Petty.

-D

Cruel but funny: 9% (60 votes)

Tall poppy put-down: 7% (50 votes)

Hurtful and uncalled for: 10% (65 votes)

Total rubbish: 14% (93 votes)

Spot on: 58% (372 votes)

HAHAHAHAHAH

Edited by AndrewJZX100
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...