Jump to content
SAU Community

Recommended Posts

i must be the only person on here actually driving their car today.

I drove today!

Bloody coilpacks. started to run on 5 :( need to get a new set, ne one got a spare liying around buy any chance. Sick of the 32 sounding like a rexxy

Anyone actually heading to BDO ?

nothing really special this year.

prodigy, hot chip, and a couple others will be good.

good perv, and always a big day out.

Cog are playing, theyre pretty damn good... listening to em now - I'd go, if it wasnt so hot and I wasnt working

-D

yeah cog are good. butterfly are ok too.

like em. but dont love em.

Thought u mighta heard of hot chip ?

Im pretty sure you were the dude I spoke to about boards of canada , art of noise etc.?

Anyone up for a late night drive tonight (like 11-12), Just fitted some new pads (750 degree pads for Mallala) and need to bed them in and it too hot during the day. Nothing too energetic as i need to get my car on the dyno to check the AFR's after the last few changes.

Just PM me if your interested and i'll get back to you around 10.

Meeting up in the NE preferably or centrally if there's interest.

Edited by D_Stirls

this is beyond a joke.

this is our 3rd power cut since 5 pm yesterday.

and our 2nd today, power went off at 1, come back at 5 only to have it back off ten mins ago..

once again FUUUK YOU ETSA!!

thanks for yet another sleepless night.

campbelltown... wierd thing is, its not as many houses as last night, and the street lights

are still on :) (last night they where off...

still, either way i look at it, im hot, and this sucks major cock!

ETSA Current outages are listed here:

http://etsa.com.au/current_interruptions.jsp?xcid=852

campbeltown isnt on there so something is not right.. your not part of the current rolling blackout so it must be a fault/issue with your supply.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...