Jump to content
SAU Community

Recommended Posts

oh yeah

im investigating instant power for my 4wd too

http://www.dieselgasaustralia.com.au

"This Diesel/Gas system will increase power and torque by up to 20% (sometimes more). This power increase is due not only to the increased combustion efficiency, but also the LPG itself produces power as it burns. So even the most economical gas map and driving technique will produce some additional power. A more powerful setting can still produce better economy than running on straight diesel."

"The power and torque increase applies over the whole rev range. Turbo lag is all but eliminated, and engine noise and vibration is dramatically reduced all the way through to maximum revs. The driver will notice fewer gear changes and higher average speeds, particularly on hills and when towing"

and for an equivalent for what i should expect

2002 Nissan Patrol GU Coil Cab

TD42T – 4.2l 6Cyl turbo diesel

5 Speed Manual

80,000km when fitted

Average fuel consumption 15l/100km

Standard Power: (red line)

96.6hp @ 3200rpm

840lbft @ 2600rpm

DieselGas Power (green line):

141.5hp @ 2750rpm (+46%)

1295lbft @ 2040rpm (+54%)

nisperf2.jpg

so, turbo people, looking at getting a new turbo for the s14, as the stocker is one its way out. not thinking anything massive, got it down to a garrett GT28R or GT28RS, just wondering if anyone here has any experience with them? ill probably end up browsing the forced induction forum soon, just seeing if theres anyone here whos used either first.

do it matty i wanted to put the skyline on gas but couldn't fit a donut tank in the boot LPG = higher octane than fuel

only problem with gas as i know is that it just doesnt have density and it requires some special injector to force the gas into each cylinder when its under boost.... my r31 had the simple setup, where as the gas is diffused into the air pipe before the plenum, but they aren't sufficient for turbos (and the fact that the lpg burns at a higher temp which could be an issue for some turbos)

-D

so, turbo people, looking at getting a new turbo for the s14, as the stocker is one its way out. not thinking anything massive, got it down to a garrett GT28R or GT28RS, just wondering if anyone here has any experience with them? ill probably end up browsing the forced induction forum soon, just seeing if theres anyone here whos used either first.

Well depends on what your really after Dave.

I have heard of people putting R34 stock turbo on and having a decent power increase by that.

GT2871R isnt a bad option either as i think thats what Dale is running in his 180 and is making quiet nice power.

So really what you want is to find out the maximum for your other parts ie. injectors, afm and etc

and then go with a turbo that wont be maxing those components out otherwise you might as well spend a lot of $$ and get everything done....ie injectors, afm, fmic, coil packs, ecu tuning etc

Hope this helps Dave

cheers krish, completely forgot about dale. shall have to have a chat with him. 34 turbo sounds interesting, thinking lag could be an issue with the missing 500cc though. just looking for nice streetable power, somewhere around the 150-160rwkw mark.

cheers krish, completely forgot about dale. shall have to have a chat with him. 34 turbo sounds interesting, thinking lag could be an issue with the missing 500cc though. just looking for nice streetable power, somewhere around the 150-160rwkw mark.

Then for that Dave i would say go with a RB turbo

from what i have heard it reduces lag on a RB20 so it shouldnt be laggy on a SR20 me thinks

good luck with whatever you do mate

I think one of my mates chucked a R34 turbo on his RB20 and made something like 180rwkw with fmic, fuel pump, pod and 14psi of boost

so wont suprise me Dave if you make a significant gain from that mate

lol they should fix the god damn roads

some of the roads around adelaide is absolute shocking

ohh and penny if you pay yearly rego you save something like $100-$150

IMHO thats a lot of money to be saved on rego

well at least thats another months worth of insurance for me really

Yeah I have decided that next time round I will do it for 12 months.

Its just crazy that we have to pay so much just to have a car on the road.

IMO push bikes should have to pay, they use the road too!! not to mention being a major traffic hazard at times.

I should be posting in the what really pisses you off thread huh.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...