Jump to content
SAU Community

Recommended Posts

Tint a car do Midnight Express, which apparently is the darkest legal tinting option! Heard good things about it.

Before Steve gets in, i think Ric from Auto Perfection does it too :D

no its not on the 2 front windows - i found out the hard way can be 35% all round but the front windows - no more than 70%

Cara is right i have the widow tinting brochure that i got when my car was being inspected.

Taken from the brochure:

The driver and passenger windows must have a luminous transmittance of at least 70%

The windows behind the driver must have a luminous transmittance of at least 35% unless they are interior windows

The inspector had a good look at the windows in the stag when i was there on Wednesday.

Edited by DSTROY

Umm all these damm rules. :D why can't things be simple.

Thank you for the suggestions. All windows bar the front two are done, the rears do look fairly dark though.

So possibly 70% fronts??

As Andrew has said you can't go past that QFM pads, I'm using the A1RM pads, they have unbelievable cold bite (I seriously couldn't believe it), and i have used them at Mallala and pulling low 1:20's and for 15 minutes and never had any fade. Also done 2 modern Reg' events and i still have another 2 days left in the pads, that's with a few hills runs as well.

They have a 1/2 price rears deal (through GSR RallySport, who's a trader on here) as well and i got free postage as well so that's front and rear 780 degree pads for $190 posted.

Im pretty sure the QFM's are not available for skylines atm. They wont have any for about 3-4 weeks :D

Umm all these damm rules. :D why can't things be simple.

Thank you for the suggestions. All windows bar the front two are done, the rears do look fairly dark though.

So possibly 70% fronts??

My fronts where nearly as dark as the back window on the Stag but i had to rip it cos i got defected, but i'll get them done to match the rears again cos legal tint will look to see though compared to the privacy glass.

70% to be legal, darker if you want to risk being defected.

so, had a bit of trouble moving my seat rail back and forward.

solution, absolutely packed it full of some random loctite grease. (i lol'd at loctite making a product designed to stop shit sticking)

still a bit firm, but whatever, probably just the rails expanded a little when they were being welded and bound up a tiny bit. no biggie, much easier to move than it was.

lol at passed out little guy

off to melbourne tomorrow morning to buy a yellow 02 ford escape for $5999

paid $500 and $90 for air flight. got unrego vehicle permit to drive it back

need to grab 2 tyres in melbourne, fill her up, then drive back.

long day tomorrow me thinks

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...