Jump to content
SAU Community

Recommended Posts

A big ROR at those 2 in the same car.....that's like Ruby & Rhys going fishing together on a quiet Sunday afternoon. :D

Skaifey should've rigged his car to explode straight after the last lap cause Murphy reminds me of a couple of douches :D

lololololol

Yeah.. giving it a good high pressure hose down.. but i was a couple of feet away (like I usually am) and the paint just flew off.
Same thing happened to mine, took it to dazzlers after I'd got it... it had a couple of existing chips but when the sprayer hit them they flaked open

I wouldn't naturally assume its the ex owner, could have easily been someone in japan or any prior owner..

Well I took my mums VZ commodore to a carwash cafe. They used a pressure hose and paint flaked off on the door handles a little bit. This is on a 1 owner car that was just over 3 years old.
same thing happened to me with the high pressure hose flaking more paint away from a small crack in my front bar. i have never washed my skyline at those car wash joints since then. Those foam brush broom things are terrible too

+1 to all the above stories. My grey GTR rear spoiler had a little bit of paint flake off due to the high pressure hose. Every time I washed the car from then on a little bit more would flake away whether I used a sponge, the brush or hose. Remember that Japan's climate is harsher on paint than ours (snow, cyclones etc) and both my cars sat on the docks for extended periods before they could be brought into Australia.

I still use the high pressure hose but I take a bucket and sponge and use Soft Wash Gel rather than the brushes - just means that I always have to wash the car at night.

+1 to all the above stories. My grey GTR rear spoiler had a little bit of paint flake off due to the high pressure hose. Every time I washed the car from then on a little bit more would flake away whether I used a sponge, the brush or hose. Remember that Japan's climate is harsher on paint than ours (snow, cyclones etc) and both my cars sat on the docks for extended periods before they could be brought into Australia.

I still use the high pressure hose but I take a bucket and sponge and use Soft Wash Gel rather than the brushes - just means that I always have to wash the car at night.

I use the high pressure hose but from maximum distance - I never use the brushes because 4wd owners have a tendency to scrub mud off with those brushes and not rinse them - that aside, the brushhairs are rather coarse and can scratch the better paintjobs out there...

in either case, i've found that elbow grease of some sort is required...

i use the pre-soak at dazzlers, wipe it down with a chammois to get rid of the brake dust, exhaust dust and assorted grit

then the soapy high pressure hose, and use a flannel with either some degreaser or bam to get rid of the stuff that is stuck to the paint... then i rinse it down, apply a hot wax and then rinse it off with the spot free finish

its very frustrating when your paint flakes (and it can happen with a hand wash too) but from what I've read, most japanese based resprays are done on the cheap because the owner is simply trying to get rid of the car

-D

Looks porn Dave!

I wash my car in my driveway, using a hose, bucket and meguiars lambswool wash mit. Before I get dobbed into SA Water, come take a look at my 3X 24,000 litre rainwater tanks. :D

Ive never used a self serve carwash on any car Ive owned, and Ive never put the R32 through a auto one.

the rims say yes.

the spoiler says no.

possibly lacking front lower lip? still hawt rims and car combo

haha, many people seem to share that opinion. but the spoiler sorta works with late 90's thing ive got going on, when factory aero and mesh wheels were cool.

makes the rear end a helluva lot more stable at speeds aswell.

but yeah, its missing the front lip. trying to find one, and i aint buying new from nissan, $500 for a lip is retarded.

the rims say yes.

the spoiler says no.

possibly lacking front lower lip? still hawt rims and car combo

i dunno mane i quite like the spoiler... looks diff to the stockers you see out there without the spoiler

i reckon if it was curved more and slightly lower to the boot it'd look better, but i cant fault the look of that car

red ones go fast

-D

front lip would be a win for sure, spose its SA so you can go too over the top but moar low w/ lip scraping on ground would get me wet. no lie.

lol, its plenty low as it is. scrapes on everything. but yeah, definitely want a front lip, only thing im not 100% satisfied with.

i dunno mane i quite like the spoiler... looks diff to the stockers you see out there without the spoiler

i reckon if it was curved more and slightly lower to the boot it'd look better, but i cant fault the look of that car

red ones go fast

-D

haha, its funny, up until a couple days ago, i owned 2 of 6 of those wings in aus.

Car is almost all ready for inspection. Changed all suspension arms over - Caster, front and rear camber, traction arms, coils, toe arms, removed cage and put stockies on the front.

Just stuck on removing this boss kit that isnt moving :D wheel is off but bosskit is stuck. After that just need to wire up a rear eye level brake light and put back seat in.

Hope i can get it cleared by the end of the week.

All good mate. Just makes me do things i wanted to do already to the car alot faster. Now all the suspension it out i can clean it all up makes sure there all working properly. Just little things i need to fix like the front window tint, its 35% and needs to be 70% and wire up a eye level brake light.

After that i'll take it outside, all wheels off and high pressure everything. Then back on the hoist for one last inspection.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...