Jump to content
SAU Community

Recommended Posts

Dropping the car into Pitlane Performance tonight, gotta get a couple things fixed up. Spoke to Simon, was more than happy for me to drop it off at around 6pm, then stay to have a look! Good to have some workshop flexibility in the north!

Dropping the car into Pitlane Performance tonight, gotta get a couple things fixed up. Spoke to Simon, was more than happy for me to drop it off at around 6pm, then stay to have a look! Good to have some workshop flexibility in the north!

thats awesome to hear Damo...not a lot of workshops do that......plus its up north as well

Dropping the car into Pitlane Performance tonight, gotta get a couple things fixed up. Spoke to Simon, was more than happy for me to drop it off at around 6pm, then stay to have a look! Good to have some workshop flexibility in the north!

Just came from there now, get Simon to take you for a spin in his RB30DET powered R33 if he's still got it..... All I'm going to say is HOLY FARK!!!! :P

Nice 1 Ruby. Enjoy :P

ruby what type of rims u looking for. possibly getting new rims for my ride soon, so the TE37's will be for sale. totally immaculate.

17s or 18s ... for cheaper rubber. Ideally, I'm looking to swap the 19" Impuls for something similar or whatever will suit the white 33. PM me so the Mods don't get too upset about a FS discussion in Wasteland.

ewwwww impuls with 0 dish ;)

cant be any worse than rjr rims though :kiss:

and yes, i can tease, beacause i used to have fail spec rims.

:P I was about to point that out too. :D

Meh, I still like em ... but I am holding out for Ben's GTR rims ;) C'mon Grim!

I have no defense for the Impuls ... they came with the car and I am getting rid of them. I do like them, but its just too big and zero dish/minor lip. At least the RJR rims have some lip.

lol this might help....its always useful/helpful if your work is willing to allow you to use their letter head

* you need your license for your work and without it you cannot go to work because of odd hours of work

* you have learnt your lesson in doing whatever you were caught doing so man times

* you will never commit those offenses again

Good luck mitch

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...