Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

ok i changed the ecu still nothing its still a s1 ecu

with my motor i stripped all s2 electronic parts off it and put all my s1 parts on it

im pretty sure the motor was a s1 out of a auto stagea i just have no power at all nohting to dash lighst nothin ??

well thats what im trying to find is there any main power wire

its hard to find thinsga cause i have a greddy plenum on it now also

when i was charging the battery from under the boonet the dash lights came up with a real slow flash and a beep like when u leave your door open ???

but now there is nothing when i turn the key i get nothing

i cant see any more wires at all on both sides worst thing is i live in a country two 10 hours from sydney 6 form melb and 4 form adelaide so yer ................rooted??

sounds like a dead battery. You shouldnt be charging the battery with it still connected to the car.

Pull it out and give it a decent deep cycle charge (ie leave it on charge for at least 24hrs). Battery chargers charge at a very low ampage so it takes a while.

If its not that the battery its a main power connection thats not connected properly. Make sure your getting a good contact at the major areas like the battery terminals and the earth lines to the engine itself.

if you put the terminals on backwards i would say the main realy woulda blown but as long as you havent done that it should be fine, its designed to jump start the car so i couldnt do any damage just wont charge the battery effectivly

as mentioned b4 i think its cos you have a motor/ecu mismatch. the series 1 stageas were based on the series 2 r33 (rb25) and series 2 stags on the r34 (rb25neo). so if like you said you stripped all the wiring off and are trying to use the wiring from a series 1 r33 rb25 it wont work. you dont have an ignitor. find a series 2 r33 or a series 1 stagea ecu and try that

ill try a r33 series two ecu but what about my ignitor how do i get passed that ?? i have one and if i put a series two ecu in they dont have a sepreate ignitor

i still have the coil packs from the series 2 so i can put them in

i dont think it is the battery cause i had a jumper pack on and it still didnt go

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...