Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

have you tried cranking over crank with a ratchet just to make sure it hasnt seized, if it hasn't as long as when you changed all your electrics over you put your series 1 coil packs and igniter over then you should use the series 1 ecu and it should work. only thing left is a loose connection or blown fuse or realy, easist to pull out all the fuses check if they are ok, i dun remember how to check relays mabye try swaping the mayor ones around if there are any and smell then see if they smell burnt out, then if that fails start checking ALL of your connections you have made make sure everything is hooked up and hooked up correctly and properly

Dont dry cell batteries need a charger with a lot more oomph than normal batteries?

What sort of battery do you have and what charger are you using?

I had my dry cell on charge with a small charger for quite a few days...lol it didnt work at all :)

Maybe try a new battery (not a new dry cell they can be $$$$) at least it will rule it out.

well i brought a new battery its worked well sort of

it primes everything up all sweet n shit all lights work

but its wont fire the starter motor

can i have put the wires on the wrong terminals on the starter motor

does anyone have pic of whet side they go on ??

Noone on here will be able to tell you with certainty what your problem is. Grab your multimeter and start by checking the voltage across the starter motor when trying to start and if that's no good check for continuity (resistance) between the ecu (pin 43 i believe, but check this) and starter, check the fuse etc. There isn't much really to the circuit apart from the ignition barrell. If the ECU isn't sending the correct signal (eg. series 1 vs 2) then you have basically no chance.

Is the ECU spitting out any error codes? Is there power to anything else? (water temp sensor, CAS, AFM, coils, fuel pump as random examples)

Edited by govich
Noone on here will be able to tell you with certainty what your problem is. Grab your multimeter and start by checking the voltage across the starter motor when trying to start and if that's no good check for continuity (resistance) between the ecu (pin 43 i believe, but check this) and starter, check the fuse etc. There isn't much really to the circuit apart from the ignition barrell. If the ECU isn't sending the correct signal (eg. series 1 vs 2) then you have basically no chance.

Is the ECU spitting out any error codes? Is there power to anything else? (water temp sensor, CAS, AFM, coils, fuel pump as random examples)

i know that but im elimanating anythin possiable

error codes ?? how do i find this out

and where is pin 43 on the ecu

my hole wiring loom in s1 any wires or elec componants are s1 all i dont was use the head and block

when you say you dont have any spark or inj do you mean the starter try's to crank it but it doesnt turn over just going tick tick tick?? are both the injectors and spark not working how have you tested for both? is the fuel pump priming?

Try swaping with a known good series 1 ecu, make sure the ignitor pack is plugged in properly, double check you havent missed pluggin in any of the connections. are the ignigtor packs known to be good?? stupid question but did you transfer over your spark plugs sometimes people forget the obvious things.

when you say you dont have any spark or inj do you mean the starter try's to crank it but it doesnt turn over just going tick tick tick?? are both the injectors and spark not working how have you tested for both? is the fuel pump priming?

Try swaping with a known good series 1 ecu, make sure the ignitor pack is plugged in properly, double check you havent missed pluggin in any of the connections. are the ignigtor packs known to be good?? stupid question but did you transfer over your spark plugs sometimes people forget the obvious things.

i have plugged everythihng in

the pump is priming

its turning over

the ignightor pack is pluged in

spark plugs are in

i tested them all

spark plugs not sparking

inj not pulsing

all tested

  • 3 months later...

have ya found out what the problem is yet with your car

i have a similar problem at the moment. The car was running previously but then now wont start. The engine is turning over but just wont start.

different power fc's have already been tried. Spark plugs, coilpacks, different CAS will be looked at monday.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...