Jump to content
SAU Community

Is It Possible? - Standard Gtr Seat Rails For A Recaro Sr3?

Owgasm

By Owgasm,
in Fabrication

 Share

Recommended Posts

Owgasm Grand Master

Owgasm

Posted
Posted

Hey,

Just got some SR3's and now looking to fit them into the car when it gets back.

Is there anyway to get the GTR rails to fit the recaro seats?

P.S if this is the wrong section or a repost of some sort, please delete this and point me in the right direction. and not to the search function.

Duncan Grand Master

Duncan

Posted
Posted

not really, skylines have a nasty shaped floor plan which makes it very hard to get a seat rail right.

By far the easiest way to go is to buy the bride rails, they bolt straight in.

If you want to do it with generic rails there will be a lot of reinforcing, welding and cuting. And I don't think you should stuff around with seat mounts unless you are really confident

Duncan Grand Master

Duncan

Posted
Posted

I'm 6'3" and don't hit the roof. I do hit the roll cage with the side of my helmet but that probably isn't an issue for most road cars. Would also depend what seat some are higher than others, and what angle you have the back at - mine is fixed back race seat.

KLR33 Community Regular

KLR33

Posted
Posted

heres how mine r done

could have been a bit neater but i was in a rush n they have been fine for the last year

they do sit a bit high but its not a drama unless u have a cage as duncan said before, and

i could not get them lower without cutting the body support the stock seat sits on

post-32345-1192637877_thumb.jpg

post-32345-1192637914_thumb.jpg

post-32345-1192637953_thumb.jpg

post-32345-1192638020_thumb.jpg

post-32345-1192638048_thumb.jpg

WRRR Rising Star

WRRR

Posted
Posted
ok, i guess i'm gonna have to find rails.

Are passenger rails different to drivers?

Try the bride rails to suit SR3 for the GTR. Driver and passenger are different.

I got some RX rails from Jackie at CJ Motors on Nissan Silvia. They were about $250 each delivered from memory. They are meant to drop the seat position by about 30mm which should leave the SR3 at a similar height to standard as they seem to have more seat base height than the GTR seats.

My new SR3's just landed from J and are due to go in when I drop some lard lol - just a wee bit tight for road comfort - probably tolerable on the track. Off for a run we go....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • GoHashiriya
      R34 Skyline Sunroof Won't Tilt/Vent

      By GoHashiriya · Posted

      I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • GTSBoy
      R34 Skyline Sunroof Won't Tilt/Vent

      By GTSBoy · Posted

      Something's broken.
    • PranK
      Shoota's R33 GT-R RB30/26

      By PranK · Posted

      It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • ShezzDogs
      R34 Skyline Sunroof Won't Tilt/Vent

      By ShezzDogs · Posted

      Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
×
×
  • Create New...