Jump to content
SAU Community

Recommended Posts

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Jamie - I will take the s/s xforce dump pipes (with O2 sensors) as discussed on the phone (Wed 24th @ 12pm).

PM postage costs and bank details please..

Cheers

Pete

interested in turbos and actuators have r32 gtr would i need anything else to bolt these on? what psi been run at and 1000ks on road or track cheers.

I wish i had a chance to get it out to the track but unfortunately season has come to an end

all kms were done on road and dyno, they were run at 14 psi cause pump maxed out ( a shame cause it would have made some good power on 20-25 psi) got 310kw at that boost level

depends what parts you have already eg: all plumbing, oil-water lines, dumps o2's, manifolds etc

let me know what you have and i'll see what else i have got...

kind regards jamie

I wish i had a chance to get it out to the track but unfortunately season has come to an end

all kms were done on road and dyno, they were run at 14 psi cause pump maxed out ( a shame cause it would have made some good power on 20-25 psi) got 310kw at that boost level

depends what parts you have already eg: all plumbing, oil-water lines, dumps o2's, manifolds etc

let me know what you have and i'll see what else i have got...

kind regards jamie

turbos and actuators sold pending $$$

hey, u wouldnt happen to have the seat belt stalk thing would u? the bit that holds the seat belt out towards the seat.

no stalk if you find one or more let me know theyre hard to find

pistons still there, give us a call if your keen 0415 405 487

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...