Jump to content
SAU Community

Recommended Posts

Dyno will be located NOR in Balga.

Its not really about thrashing your engine if more making sure its healthy. PLug the wideband unit in check afr's

Also to be used for tunning your car as will will have most tuning software/hardware there.

Looking at buying the dyno soon and just wanting to see how much use it will get to help pay the payments on it

Link to comment
https://www.sau.com.au/forums/topic/189712-dyno-use/#findComment-3418625
Share on other sites

Yes me and my business partner are buying a dyno for our workshop.

This is only a part time thing for now but hopefully will turn out to be a full time job.

We have been looking around at hiring dyno's for tuning and found them really expensive.

We figured 2 runs a week will pay off buying our own.

So if we get it i want to offer it to people at a much lower price as i know how hard it is to get time with one.

Link to comment
https://www.sau.com.au/forums/topic/189712-dyno-use/#findComment-3419044
Share on other sites

I'd pay money to use it for an hour or so once I get my engine in, then again when its run in and boosted up. Would be great to be able to use a dyno to DIY tune rather than using the road.

Would also be cool if you did a cheap R32 reflash & tune. If you want any technical info on it let me know.

Link to comment
https://www.sau.com.au/forums/topic/189712-dyno-use/#findComment-3420433
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...