Jump to content
SAU Community

Recommended Posts

I have a series 1 R33 GTS-T.

When i reverse up the driveway i can hear a rattle that sounds like it's coming from the top of the right rear shock. I checked that all the bottom of the assembly is tight so it seems to be the top nut / nuts have come loose. I removed the carpet panels from inside the boot and can see the surround where the shock would sit inside but cannot find a rubber to remove to tighten the top nut / nuts. I searched through these forums and found 1 reference to it but it was based on an R32.

R32/33: Replacing Shocks / Installing Coilovers

It looks to me like i may need to remove the back seat, then the parcel shelf to get to it?

Any help or advice would be much appreciated!

Link to comment
https://www.sau.com.au/forums/topic/190550-r33-gts-t-rear-shock-removal/
Share on other sites

no problem.. alternatively you can smash the rear window and rip out the parcel shelf... thats how i removed them when my car was written off. :rolleyes:

After reading the "Skyline R33 Rear Seat Removal Pictorial Guide" (minus pictorial!!!) it might be easier to smash the window!

Skyline R33 Rear Seat Removal Pictorial Guide

its not *that hard*...

undo the bolts in the bottom of the seat, then the bottom will unclip (with a bit of force, i usually stick my breaker bar though the loop, and give it a pull upwards),

undo the bolts in the bottom corners of the top of the seat, and it will lift up and off,

then the parcel shelf should just lift off, and you are done.

Takes about 5 minutes to have the whole back seats and parcel shelf out once you've done it a few times. Trickiest bit is getting the seat base out of the clips if your afraid you'll break something.

My advice is to have a crowbar and dont be afraid to break the clips as they wont.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...