Jump to content
SAU Community

Recommended Posts

After some "spirited" driving on the weekend my ATTESSA has decided to put most/all the power to the rear wheels. My dash light is off and the torque spilt gauge is working fine but 3rd gear fishies mean something is playing up.

Now I'm assuming that the transfer case is gone, which I'll just replace if it has but I'm crossing my fingers that because the fluid in the tank is a bit low (just under min) it may have got a airlock in the system. I know how to bleed the system and have some nissan fluid to do it and will try on the weekend...

But in the meantime am i just wasting my time because its definatley the transfer case or is it worth bleeding the system?!?

Link to comment
https://www.sau.com.au/forums/topic/190708-attessa-problem-r32-gtr/
Share on other sites

well i did say spirited driving haha

oh yeah the other thing i did that might mess things up was switch the car from 4wd to 2wd while the atessa was working very hard...

would this have done anything to the computer etc to cause this?!?

sorry guys for butting in. I tried bleeding the ATTESA sytem when i first got the car. You have to disconnect the green plug at the kicker plate. It was damn hard and i coulnt disconnect it. Any tips??? As how to disconnect the plug easily? Cos i have topen up the line at the underneath the rear of the transmission. Cos i got a leak on it andd im trying to determine whete is the gasket or an O ring on the fitting. But before i take the line out i have to make sure that im able to bleed the system after. Lemme know. thanks

Yudy

The transfer case uses a wet clutch system. These clutch plates only have a finite life, and 10+ years is well and truly in the "finite" catagory.

When you rebuild the case you can squeeze some extra plates in there (along with a couple of extra "tricks") to give a really quick uptake. Combine this with an ATESSA controller and your R32 will be transformed on the track.

The transfer case uses a wet clutch system. These clutch plates only have a finite life, and 10+ years is well and truly in the "finite" catagory.

When you rebuild the case you can squeeze some extra plates in there (along with a couple of extra "tricks") to give a really quick uptake. Combine this with an ATESSA controller and your R32 will be transformed on the track.

but i dont wanna put u to shame gav :rolleyes:

  • 3 weeks later...

ok i finally got around to bleeding the system on the weekend... its seems to be fine and have no air in it.

BUT

while i was changing it i noticed that the attessa pumps would kick in for no reason every 10 sec or so when car was just idling, you can clearly hear a relay clicking and then when bleeding from the nipple above the diff a tiny little burst would come out with what looked like air.

plus on top of this the fluid resivoir has the top section and then the bottom section, with a spacer between. in all systems other than mine the bottom section has a air space in it... mine doesnt

any comments suggestions thoughts?!?

Edited by Cerbera

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
×
×
  • Create New...