Jump to content
SAU Community

1993 R32 Gtst With Rb25

Bunta

By Bunta,
in Classifieds

 Share

Recommended Posts

Bunta Grand Master

Bunta

Posted
Posted

a 1993 R32 GTST 179000 on the dial Suspension was installed at 170000, engine was installed a 171000 as was the clutch, and the turbo has covered less than 2000 km

R33 RB25DET

20 thou oversize forged pistons

forged h beam rods

reconditioned (new springs valves ect) and lightly ported head

N1 oil and water pumps

ACL race bearings

Cometic metal head gasket

ARP head studs and rod bolts

R33 Gearbox

R33 Differential

Garrett GT3076R Turbo

Tomei Poncams

600cc injectors

Z32AFM

HKS Hyper 3.5" exhaust with custom front pipe

Splitfire Coil Packs

OSgiken TS2BD twin plate clutch rebuilt by NPC

C’s Short Shifter

GFB Stealth FX Blow off valve

Bosch 700hp rated fuel pump

Apexi Pod Filter

Apexi PowerFC

Greddy Profec B spec 2 Boost controller

Custom FMIC

Custom intake piping

Oil cooler and filter relocation kit

Suspension and Braking

HKS Hypermax 2 coil over suspension

Front and rear strut bars

B pillar Brace

After market sway bars

JIC adjustable castor rods

JIC adjustable upper arms

Whiteline Pineapples

R33 GTR Brembos with DBA 5000 rotors

Front: 17 X 8 wheels with 235/40 semislicks

Rear: 17 X 9 wheels with 255/40 semislicks

Exterior and interior

Full respray- Custom Blue

Genuine GTR Bonnet and Grill, Front bar, and rear spoiler

GTST Type M side skirts

GTST Type M rear pods

Genuine R32 GTR Front and Rear seats

Genuine R32 GTR Door trims

Genuine R32 GTR Headlights

Nismo Gearknob

Audio

DVD player with 4 inch screen

6.5" Jensons in the back and JL 6" Splits @ the front

Last tune was a very safe 260rwkw it was making 300rwkw previously but it was not safe, a safe 300rwkw is only a thicker head gasket away! At 260rwkw this thing still really hauls and handles beautifly too as it has that little bit of extra attention paid to the suspension

I am asking 24,000 neg. this price is mostly designed to ward off dreamers and tyre kickers, if you are interested we will talk! I have included a picture of the car with 18inch starcorp impuls, if the buyer perfers these wheels could go on the car instead as I still have them at home.

PM me to discuss the car. Hope to hear from you soon!

Andy

OFFERS AROUND 20K WILL GET YOU THIS CAR TODAY!!

post-21318-1193703070_thumb.jpg

post-21318-1193703223_thumb.jpg

post-21318-1193703242_thumb.jpg

post-21318-1193703254_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191365-1993-r32-gtst-with-rb25/
Share on other sites
Bunta Grand Master

Bunta

Posted
  • Author
Posted

Thanks for the kind comments guys! It will be sad to see her go after all the blood sweat and tears but after the best part of 2 years i am ready for a change!

Bunta Grand Master

Bunta

Posted
  • Author
Posted
my kind of no bullshit car!

ive never seen it... shooooooooooow me.

you could but it and see it all the time :ninja: ha ha I will even give you a special members price :)

Oblivion Grand Master

Oblivion

Posted
Posted

someone buy this car.....this is an awesomely kept and run car has everything you need and nothing to put in except fuel...

I have been in this car and its a wet dream on wheels.

  • 1 month later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...