Jump to content
SAU Community

Recommended Posts

Hi, I have a problem with my car overboosting and causing it to knock

here is my set up

GCG HF/BB

555 HKS injectors

Pro spec B2 B/C

FMIC

it was set to 15psi high boost and 10psi low boost on the dyno

on the road high boost climbs to 17.7 psi and low to 12.2psi low

my boost controller on high is set at

gain 15%

set gain at 50

the over boost cause to knock after 6000rpm

any ideas why

cheers

joe

Link to comment
https://www.sau.com.au/forums/topic/192179-overboosting-knocking/
Share on other sites

when my m8s car was on high boost it started knocking at high revs... then at most revs... then at all revs... the knocking getting worse and worse... turned out he had done a big end bearing. probly nothing this major in your car just a thought thats all

running power FC

had a knock reading of 94

on the dyno it showed a nice straight line at 15psi at peak getting 252rwkw

Take it to your tuner and get him to adjust the tune - it's not a matter of adjusting the boost controller, esp considering on a freezing night you'd be likely to get a spike again anyway... rather you should try to ensure the tune is better...

So speak to your tuner :ninja:

Take it to your tuner and get him to adjust the tune - it's not a matter of adjusting the boost controller, esp considering on a freezing night you'd be likely to get a spike again anyway... rather you should try to ensure the tune is better...

So speak to your tuner :ninja:

this is been an ongoing problem on dyno its sweet on the road in spikes even with the boost contoller of it boosts to 12psi

even with a perfect EBC it'll still spike a bit - I'm surprised your tune is so close to the limit that a tad more boost causes knocking. Why not richen up the tune (or take out a tad of timing) a little so at least you can drive the thing properly whilst identifying your issue :ninja:

Edited by TommO

Thanks everyone, its really fustraiting me I had the spike problem with it before, i was informed that the OP6 housing will fix it. but im back to square 1

I'm to the tuner 2moro

if i get them to tune

13psi high boost do on the road i should get 15psi

8 psi low road 10psi

maybe that will work

why don't you just have one tune at one set boost, and control the power with your foot?

I have one tune running 300rwkw and 18psi of boost.

When I want half power, I use half throttle?

Edited by The Mafia
why don't you just have one tune at one set boost, and control the power with your foot?

I have one tune running 300rwkw and 18psi of boost.

When I want half power, I use half throttle?

how do you do that when its on man.. all you wanna do full throttle and punch the gears,

how do you get 300 stock engine no knock

how do you do that when its on man.. all you wanna do full throttle and punch the gears,

how do you get 300 stock engine no knock

a decent tune.

I ran 370rwkw, no spike, no knock.

Its a combination of things.

Plus your running a PFC - so you cant have two maps unless your running a datalogit and change it everytime you change boost setting.

Power/boost is controlled by the right foot. I ran 24psi daily without issue

a decent tune.

I ran 370rwkw, no spike, no knock.

Its a combination of things.

Plus your running a PFC - so you cant have two maps unless your running a datalogit and change it everytime you change boost setting.

Power/boost is controlled by the right foot. I ran 24psi daily without issue

370rwkw with the RB25?

Sounds like a handful lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...