Jump to content
SAU Community

Recommended Posts

me and rodney (GOR33) met her the other week cause she was doing about 50 non stop tuff laps around surfers

so we puuled her over

conversation

first off we could not stop laughing at her cause she kept on doing laps around surfers.

then we started playin silly buggers

she pulled over so we got rodney to sneek up behind her car and snap a picture of her then we continued to piss ourselves laughing cause she was not impressed

about 20 laps later we ran out in front of her car to try and talk to her.

she nearly ran us over.

another 20 laps later we yelled out for her to pull over and talk to us

she did so me and rod walked up to the window

Rodney: hey hows it going

NIS533: ahhh alright

Rodney: So are you on the forums?

NIS533: what

Rodney: you know internet on the Skyline forums

NIS533: why

ME and Rod: cause there are big skyline cruises and meets and make freinds and what not come on SAU Skylines Australia

NIS533: nah i dont couldnt be bothered or somethin

Rod: So does it go alright goes good?

NIS533: yeah

ROD: what has been done to it?

NIS533: i dont know my friend does it up

Rod: riiiiiiggggghhhhttttt so its got lots of power hey

NIS533: yeah

Rod :it must go preety good cause of all the PU55Y POWER (She has a pu55y power sticker all over the back window.

and after all this with me laughin my head of and rod crackin up as well she didnt even crack a smile

conclusion: NIS533 uses the most petrol on the coast and doesnt think rodneys funny if rodney cant make her laugh noone will

Rodney you da funny man

pitty his car seems to break for a day then comes good :D

Rodney you better come out tonight

hahahahahahahahaha was that your old car, *** those plates, i knew ive seen them sumwere

man shes putting out ****en lion power or sumthin, that was no kitten,sic lookin car;)

slide needs an award people, i wish to nominate him for the 110% award:) hahahahaha

Midnight Purple 34 GTR (GTR 38) spotted driving down Turbot at lunchtime today.

 

101cafe stickers on it and a huge set of Volk GT-C's rims :aroused:

That thing is f'ing tough aye. I saw him up the sunny coast a few weeks back when I had the day off. He looked at my car like wtf is that. I looked at his car with my jaw draging along the road.

Silver 32 GTR (maybe GTS-t, I was driving in opposite direction at more or less the posted speed limit) (cunningham highway,swanbank 1pm you were headed inbound )

Smashed bonnet, looked like the bonnet latch came undone, looked pretty nasty. Hope your OK, and that the damage is limited to the bonnet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...