Jump to content
SAU Community

Recommended Posts

  • Replies 266
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

VR ftw. From the factory it molests any RB. Just wait til modified VR's begins raping N1 RB's... :nyaanyaa:

And why are you hoe's comparing a Z-tune RB to the VR???

Yes they're the same HP from the factory but...ready...the Z-tune is the BEST GTR money can buy and now the R35 is out, it will keep up with Z-tune but isn't limited to only 20 freaakin models :) . We can all have one (tug-tug, ahem...)

It's a muthaflippin' miracle! ;)

hahahaha to ALL !!!!

VR38DETT NEW GTR UPGRADE VERY EASY BROKEN BLOCK !!! BECAUSE BLOCK FROM ALUMINUM HAHAHAH :)

NOTE : ATTENTION TO ALL !!! :D

Thank alllllllllll .......LLOOOLLL :)

Where did you get this information from?

How many R35's do you know that have cracked their Blocks?

Dude... use logic. Nissan would not make a fragile Hero Car that they've been building up for 6 years...

ffs...

hahahaha to ALL !!!!

VR38DETT NEW GTR UPGRADE VERY EASY BROKEN BLOCK !!! BECAUSE BLOCK FROM ALUMINUM HAHAHAH :)

NOTE : ATTENTION TO ALL !!! :D

Thank alllllllllll .......LLOOOLLL :)

agreed... vr block aluminium coke can... easy broke fail... rb engine iron block... like iron man... unbeatable

hahahaha to ALL !!!!

VR38DETT NEW GTR UPGRADE VERY EASY BROKEN BLOCK !!! BECAUSE BLOCK FROM ALUMINUM HAHAHAH :)

NOTE : ATTENTION TO ALL !!! :D

Thank alllllllllll .......LLOOOLLL :)

i say we get a RB26 running 500hp on stock internals and put it up against the VR38.

hahahaha to ALL !!!!

VR38DETT NEW GTR UPGRADE VERY EASY BROKEN BLOCK !!! BECAUSE BLOCK FROM ALUMINUM HAHAHAH :)

NOTE : ATTENTION TO ALL !!! :D

Thank alllllllllll .......LLOOOLLL :)

351 Cleveland > RB26DETT, IRON HEAD NOT CRACK LIKE RB HEAD....

PUSH RODS BETTER THAN DOHC....

THANKS ALLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL

Where did you get this information from?

How many R35's do you know that have cracked their Blocks?

Dude... use logic. Nissan would not make a fragile Hero Car that they've been building up for 6 years...

ffs..

Know will be seen soon!! Do not forget that the Fund Gears electronic malfunction that will cause many, especially if upgrading engine!!!! :D;):ermm:

hahahaha to ALL !!!!

VR38DETT NEW GTR UPGRADE VERY EASY BROKEN BLOCK !!! BECAUSE BLOCK FROM ALUMINUM HAHAHAH :ermm:

NOTE : ATTENTION TO ALL !!! :)

Thank alllllllllll .......LLOOOLLL :D

Know will be seen soon!! Do not forget that the Fund Gears electronic malfunction that will cause many, especially if upgrading engine!!!! :ermm::ermm::D

Yes soon we will all know the dark secret of Nissan...stinging out on us by using aluminium and not iron...the goat herder from kuwait imparts his knowledge - his deep engineering/mechanical understanding overshadowing a multi-million dollar company staffed by qualified engineers.

Oh nos Nissan! Recall your GTR's before everyone becomes disappointed. I wish I had 4 thumbs so I could give bkc 4 thumbs down :down::down::down::down:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...