Jump to content
SAU Community

Recommended Posts

Just after a ball park figure as to what i can expect at the rear wheels with the following mods on my r32 RB20.

Hybrid copy intercooler.

Currently running an r34 turbo with rb20 waste gate actuator and turbo smart boost controller, will be fitting a GCG 450 HP rb25 hi flow on friday.

split dump, going into a huge 88mm stainless front pipe, standard cat and 2 7/8" cat back.

Adjustable cam gears set at +3 inlet, -5 exhaust (crank Degrees)

GTR injectors

Z32 AFM

040 fuel pump

Intercooler piping over radiator is wrapped but am getting the 120 degree pipe made up on weekend (intercooler to TB)

homemade CAI with enclosed pod. Been monitoring intake temps at throttle body with jaycar temp sensor (reads -50 to 150 C) and temps have been only a couple degrees hotter than ambient at 14PSI.

Am running Nistune daughter board which makes standard ECU fully programmable, also tech edge wideband sensor to monitor A/f ratios to which i have also wired up a 3 bar map sensor to monitor boost pressures through data logging.

Just after a ball park figure.

Thanks.

Edited by kjb_r33
Link to comment
https://www.sau.com.au/forums/topic/192643-what-to-expect/
Share on other sites

Yes mate as R31 Nismoid said should acheive

around 180 - 240 rwkw one thing to remember is

that all dynos read different some higher some

lower as for your cam gears I spoke to Dr Drift

and he suggusted for a good mid range responce

set up aim for 5deg advance on inlet and 2deg

retart on exhaust.I have yet to try these settings

I'm waiting for my next track day to give them a

go myself.Hope this is of some help

Link to comment
https://www.sau.com.au/forums/topic/192643-what-to-expect/#findComment-3461057
Share on other sites

Yes mate as R31 Nismoid said should acheive

around 180 - 240 rwkw one thing to remember is

that all dynos read different some higher some

lower as for your cam gears I spoke to Dr Drift

and he suggusted for a good mid range responce

set up aim for 5deg advance on inlet and 2deg

retart on exhaust.I have yet to try these settings

I'm waiting for my next track day to give them a

go myself.Hope this is of some help

Thats weird...sam set mine to +3 on inlet and -6 on exhaust...wonder what difference that makes....

Link to comment
https://www.sau.com.au/forums/topic/192643-what-to-expect/#findComment-3470659
Share on other sites

dynoed yesterday, dyno dynamics dyno, no shootout mode, pissy little fan.

Got 204 with a VERY rich safe tune at this point, too rich actually, hit 10.5 reading with a true wide band sensor, (6 wire tech edge). That was at 15 psi., ambient temp of 30 c, no pinging.

Link to comment
https://www.sau.com.au/forums/topic/192643-what-to-expect/#findComment-3470660
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This car has run before on this z32 ecu can get the part number for you, I have tried with no AFM it didn’t change anything, I compression tested today 140-150 across all 6 cylinders, also set fuel pressure to 43psi. The only weird thing was cylinder 1 plug was black and fouled other 5 cylinders were just wet with fuel. Spun cas by hand and confirmed injectors are clicking 
    • Since you came here to ask for help, have you thought about answering our questions, that might help us lead you to why it was skipping, or have you given up on getting advice?
    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
×
×
  • Create New...