Jump to content
SAU Community

Removing Gtr Spoiler?

bernard R33

By bernard R33,
in Exterior & Interior Styling

 Share

Recommended Posts

cheez Mentor

cheez

Posted
Posted

is it glued on or is it just stiff to get off?

either way if u plan to put a stealth wing on i would just use something to pry it off. at the end of the day that area will be covered with the stealth wing. also if ur getting ur wing sprayed u might as well spray the boot again at the same time. wont cost u much. maybe extra 100 - 150

NA_Goodness Grand Master

NA_Goodness

Posted
Posted

Is the spoiler on the R33 for a reason? Extra downforce at higher speeds like the Audi TT? Or is it purely cosmetic. I know you have to do some sustantial modification to have a smooth boot, and was wondering if this was a deliborate act by Nissan to prevent the removal? Sorry to highjack the thread tho.

Baz Experienced

Baz

Posted
Posted

Use a glue solvent such as brake clean of wax and grease remover. Push some underneath the spoiler and let it set. It will eventually make it a bit easier to pull off. Oh yeah and there are some clips holding it in place as well. Might as well use a rag and a dent lever to pull it off

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • jtha7
      New r33 owner

      By jtha7 · Posted

      Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...