Jump to content
SAU Community

my head light globes keep blowing up

hippy

By hippy,
in General Maintenance

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

Often a slightly intermintant electrical problem can be enough unfortunately. If a wire is lose and grounds itself to the body then POP :D Can happen so randomly, and usually its a bitch to track down the source

But moisture has been the biggest problem in lightsI have seen with blown globes.

arelh Rookie

arelh

Posted
Posted

Look at the base of the globe and all adr compliant globes have a circle with E1 inside - these globes are the best quality - thats not to say the others arent good - they may be too bright (G4's) or multi-coloured - blue coated quartz lenses like narva optiblue and philips bluevision are street legal - the blue coating helps reduce UV transmission to protect polycarb lenses

hippy Grand Master

hippy

Posted
  • Author
Posted

nah i think its more a case of grease on the globe cause the glass melted .. not the element breakin like that first one .. i was really really careful with this one so i'll let u guys know in a couple of months time if :) .. enrico .. how u going to fix it for me??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...