Jump to content
SAU Community

Recommended Posts

High mount stainless manifold, 38mm external wategate, Sliding performance built "T04R" still under warranty never been fitted or used. Good quality manifold and gate.

More specs to come when I find the info sheet.

Asking $2000 for the lot can supply exhaust flanges etc and lines as well.

Two Garrett GT2871R-10's have done 850Kms on my Brand new engine and are being removed this weekend. Im going with a twin high mount kit so these have simply been used to run an engine in and served their purpose well.

They will be cleaned and reassembled by GCG before sold to make sure they are like new still.

receipts from new can also be supplied but they are litteraly 850km's old.

all specs and comparisions can be done HERE and allternativly till the end of the week they can be veiwed on the vehicle prior to purchase.

Im asking $2500 and negotiable to a degree.

Pair of precission turbo's "N1" rebuilt turbos. These were done in '06 and now require a rebuild as they suffered an oil supply issue. Basicly they have been assessed by Precission and quoted $800 each to rebuild. They are worth 2200 new in good condition so im asking $400 as they are and I can organise repairs if need be.

Full set of RB26 rods, been shot peened and journals are closed and honed ready for use. New studs and nuts. $200

Nismo clutch plate to suit RB26 push type, next to no wear what so ever. removed due to twin plate upgrade when gearbox failed. $200

Just jap oil cooler kit. was purchased to replace my old kit but I now have another jap kit ill be using. $250

Thanks Brad

Edited by Risking
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...