Jump to content
SAU Community

Recommended Posts

S13 SR20DET COMPLETE ROCKER COVER TO SUMP ENGINE (COMES WITH ALTERNATOR, STARTER AND ENGINE LOOM, INJECTORS NOT INC), THIS ENGINE WAS BUILT AS A NO-EXPENSE SPARED EXERCISE AND SHOULD HANDLE JUST ABOUT ANYTHING., WITH A SMALL TRUST TD06S L2-20G TURBO KIT MADE A LAZY 279RWKW @ 1.3BAR WITH A LARGER TURBO HIGH 300RWKW WILL BE NO ISSUE.

Engine Specs:

JUST SOME OF THE PARTS USED….. TOTAL BILL WAS OVER 12K!!!

GREDDY PISTONS 13525802 $1559

GREDDY H-BEAM RODS 13525401 $2499

CARILLO ROD BOLTS

ARP MAINS $189

ARP HEAD STUDS $249

GREDDY HEAD GASKET 13521328 $329

GREDDY VALVE SPRINGS 13523801 $329

GREDDY STEP 2 CAM 264 11.5 13525209 $499

GREDDY STEP 2 CAM 272 11.5 13525210 $499

GREDDY CAM GEARS X2 13523303 $469

GREDDY SUMP 13525901 $549

GREDDY ROCKER STOPPERS 11522050 $139

ACL RACE BEARINGS

FULL MACHINE WORK

FULL HEAD RECO

FOR THOSE WHO WISH TO USE IT AS A COMP ENGINE I WILL ALSO INCLUDE ALL THE MODIFIED COOLING SYSTEM COMPONENTS, IT HAS ALL THE MANIFOLD AND HEATER LINES WELDED UP AND IS DESIGNED TO RUN WITH A REMOTE HEADER/SWIRLPOT. THIS ELIMINATES ALL HOSES EXCEPT FOR UPPER AND LOWER RAD HOSES. THESE COMPONENTS ARE ALL BOLTS ONS AND CAN BE REMOVED TO FIT THE STD PARTS IF YOU WISH.

FULL MACHINING WORK, DONE TO A VIRGIN BLOCK. TORQUE PLATE HONED, DECKED, LINE BORED,

HEAD FULLY RECONDITIONED, NEW LIFTERS, VALVES, VALVE SEATS AND GUIDES.

THIS ENGINE HAS DONE 5 MEETINGS AND IS AS NEW, IT WAS STRIPPED FOR INSPECTION AND HAS HAD A BRAND NEW 1.2MM HEADGASKET INSTALLED. THE ONLY REASON THIS IS FOR SALE IS THE CAR HAD A RB26DETT TRANSPLANT. CAR RAN ONLY THE BEST ENGINE OIL AND WAS CHANGED EVERY MEETING.

$6000 ono

have a set of cams to sell see link: http://www.skylinesaustralia.com/forums/Ch...ml#entry3548334

post-34927-1196048399_thumb.jpg

post-34927-1196048584_thumb.jpg

put it back in lol

nah the 26 is sorted now, the T517Z's where too linear and responsive, cut killer laps but hated drift. not agressive enough but hey. This time i get to build what i want for the 26 much like i did for this SR ...not what im asked to build :P responsive lazy power was the ask but agressive is the only way ;)

(i actually built 3, 2 for mates and one for cats car but cats had differrent rods and cams)... you being a ns.com poster would know the other two cars the engines went into.... 180athid and godhand.

I don't see a price between all that yelling ;)

i baldy locks'ed it for you :P

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi....cSELL.m315.lVI

goodluck with the sale trent this engine is a machine, same with athids engine. im sure your rb26 will be a monster aswell :P

cheers, hows yours coming along?

considering whats in the engine thats as cheap as u will find a proper built sr20...

go buy carillo rods and see what they set u back on their own... then u will appreciate this price.

good buy mate, good luck

hmmm i wish, but i dont think i want fork out that kind of money......

good luck with the sale

ps your car is the shit, best 32 in vic.

hahaha some jerk offered 1500..... i rather piss on it than sell it for that :nyaanyaa:

"Tell him his dreamin"

Am i wrong is that the drift cats car?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...