Jump to content
SAU Community

Recommended Posts

Hey all,

Im looking at buying some front vented gaurds that are 30mm wider than the standered ones. So im guessing my wheels now wont fill out the gaurds...

So i may look at some new wheels. What offsets and width should i be looking for?

What sort should i be looking at to fill out the gaurds more now... Want some dish... and under or around $2000...

Any help would be great..

Also looking at some rear over fenders... but how are these held on?? am looking to try and do it myself... ideas?

Edited by Adz2332
Link to comment
https://www.sau.com.au/forums/topic/195544-filling-out-the-gaurds/
Share on other sites

we usually grind the rear quarter back to metal, then use 3M Automix to adhere the fibreglass directly with the exposed metal... reinforce by drilling and resining through so that the overfender doesn't move around and cause hairline cracks in the paint a couple of years down the track. If the fender allows for it we may pop rivet as well for additional reinforcement, but not where the rivet has to be covered by filler to hide it, as a couple of years down the track the filler tends to shrink around the rivets and show dimples.

3M Website for Automix

we usually grind the rear quarter back to metal, then use 3M Automix to adhere the fibreglass directly with the exposed metal... reinforce by drilling and resining through so that the overfender doesn't move around and cause hairline cracks in the paint a couple of years down the track. If the fender allows for it we may pop rivet as well for additional reinforcement, but not where the rivet has to be covered by filler to hide it, as a couple of years down the track the filler tends to shrink around the rivets and show dimples.

3M Website for Automix

He's reffering to Front vented guards (replacement) not rear guards.

As for the front guards, it says 30mm wider, but they actually taper back into the door and the front bumper, so they are only 30mm wider at the middle of the guard then meet back to the factory bumper mounting points, its abit hard to explain, but when i had these guards on my r33, i could only space them out a extra 20mm or so, before rubbing. As for offset around +20 should do.. If using a bolt on spacer, go for the minimum size of 25mm, you should be fine, aslong as the car isn't overly low.

ahhhh pop riviting to the car.. hmmm no way you can do it without damaging panels??

Most people use this technique because it's cheap and it gives that 'tough' look to the car, but I don't think it's the look you're after.

He's reffering to Front vented guards (replacement) not rear guards.

As for the front guards, it says 30mm wider, but they actually taper back into the door and the front bumper, so they are only 30mm wider at the middle of the guard then meet back to the factory bumper mounting points, its abit hard to explain, but when i had these guards on my r33, i could only space them out a extra 20mm or so, before rubbing. As for offset around +20 should do.. If using a bolt on spacer, go for the minimum size of 25mm, you should be fine, aslong as the car isn't overly low.

+20? i reckon you could get away with lower than that

i had 17x8" +32 on the front of my r33, and it wasnt flush with the guards, so if you are putting on another 20-30 mm, you should be able to sneak in a gtr-ish offset rim, like +12, even if you have to add a degree of camber :)

that said, it depends on what widths you want as well..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...