Jump to content
SAU Community

Recommended Posts

Hey all,

Im looking at buying some front vented gaurds that are 30mm wider than the standered ones. So im guessing my wheels now wont fill out the gaurds...

So i may look at some new wheels. What offsets and width should i be looking for?

What sort should i be looking at to fill out the gaurds more now... Want some dish... and under or around $2000...

Any help would be great..

Also looking at some rear over fenders... but how are these held on?? am looking to try and do it myself... ideas?

Edited by Adz2332
Link to comment
https://www.sau.com.au/forums/topic/195544-filling-out-the-gaurds/
Share on other sites

we usually grind the rear quarter back to metal, then use 3M Automix to adhere the fibreglass directly with the exposed metal... reinforce by drilling and resining through so that the overfender doesn't move around and cause hairline cracks in the paint a couple of years down the track. If the fender allows for it we may pop rivet as well for additional reinforcement, but not where the rivet has to be covered by filler to hide it, as a couple of years down the track the filler tends to shrink around the rivets and show dimples.

3M Website for Automix

we usually grind the rear quarter back to metal, then use 3M Automix to adhere the fibreglass directly with the exposed metal... reinforce by drilling and resining through so that the overfender doesn't move around and cause hairline cracks in the paint a couple of years down the track. If the fender allows for it we may pop rivet as well for additional reinforcement, but not where the rivet has to be covered by filler to hide it, as a couple of years down the track the filler tends to shrink around the rivets and show dimples.

3M Website for Automix

He's reffering to Front vented guards (replacement) not rear guards.

As for the front guards, it says 30mm wider, but they actually taper back into the door and the front bumper, so they are only 30mm wider at the middle of the guard then meet back to the factory bumper mounting points, its abit hard to explain, but when i had these guards on my r33, i could only space them out a extra 20mm or so, before rubbing. As for offset around +20 should do.. If using a bolt on spacer, go for the minimum size of 25mm, you should be fine, aslong as the car isn't overly low.

ahhhh pop riviting to the car.. hmmm no way you can do it without damaging panels??

Most people use this technique because it's cheap and it gives that 'tough' look to the car, but I don't think it's the look you're after.

He's reffering to Front vented guards (replacement) not rear guards.

As for the front guards, it says 30mm wider, but they actually taper back into the door and the front bumper, so they are only 30mm wider at the middle of the guard then meet back to the factory bumper mounting points, its abit hard to explain, but when i had these guards on my r33, i could only space them out a extra 20mm or so, before rubbing. As for offset around +20 should do.. If using a bolt on spacer, go for the minimum size of 25mm, you should be fine, aslong as the car isn't overly low.

+20? i reckon you could get away with lower than that

i had 17x8" +32 on the front of my r33, and it wasnt flush with the guards, so if you are putting on another 20-30 mm, you should be able to sneak in a gtr-ish offset rim, like +12, even if you have to add a degree of camber :)

that said, it depends on what widths you want as well..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...