Jump to content
SAU Community

Recommended Posts

I fang mine around all the time. I'm not saying this to sound cool. I just dont drive it like a granny. Im not really fussed about fuel consumption as I didnt buy the car for that.

Before you say I drive like a dick, I dont swerve in and out of traffic, dont speed in excess and never lost a point. I just sit a gear lower than I should all the time :thumbsup:

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

^^^ that's crazy man..

you'll wreck your engine.

You gotta warm it up..

like me..

each night, I put a container of oil in to a speacially built room which is heated to 80 degrees.

before I start my car in the morning, I pull the head off and put a little bit of this pre-heated oil in the pistons to make sure they are lubricated and warm.

I then torque down the head and put it all back together.

I then proceed to take the turbo off, pull it apart and lubricate the bearings with the same pre-heated oil.

I then put it back on.

Then, I pull the injectors off, put a little bit of fuel in them and install them back in.

I remove the spark plugs, put them in the heated room for 20 minutes to warm them up, then install them back in the car.

THEN, I put the key in the ignition, turn it to reds and wait for the pump to prime.

Then I crank it over and start the car.

At this point, I let the car idle for 55 minutes exactly to make sure it has warmed up properly.

While it is doing that, I jack up the car and spin the wheels by hand then run to the drivers side and step on the brake.

I do this about 15 times to get a little bit of heat in to the brakes.

after 55 minutes have passed, I remove my tyre warmers and thermal blanket off the car and drive slowly, making sure I don't go over 0 on the boost gauge and not over 1500rpm on the tacho.. for at least the next 10 minutes.

At this point, it is safe to drive the car to a maximum of 3200rpm.. you don't want to thrash them over that..

Revs kills engines you know..

This routine takes about 12 hours each morning, but it is well worth it.

I strongly suggest you all do the same thing..

You would if you really cared about your skyline.

I dunno..

I mean to save all that trouble, I would just up the time spent on limiter to about 6 minutes.

While it is doing that, I jack up the car and spin the wheels by hand then run to the drivers side and step on the brake.

I do this about 15 times to get a little bit of heat in to the brakes.

Gold! LOL

^^^ that's crazy man..

you'll wreck your engine.

You gotta warm it up..

like me..

each night, I put a container of oil in to a speacially built room which is heated to 80 degrees.

before I start my car in the morning, I pull the head off and put a little bit of this pre-heated oil in the pistons to make sure they are lubricated and warm.

I then torque down the head and put it all back together.

I then proceed to take the turbo off, pull it apart and lubricate the bearings with the same pre-heated oil.

I then put it back on.

Then, I pull the injectors off, put a little bit of fuel in them and install them back in.

I remove the spark plugs, put them in the heated room for 20 minutes to warm them up, then install them back in the car.

THEN, I put the key in the ignition, turn it to reds and wait for the pump to prime.

Then I crank it over and start the car.

At this point, I let the car idle for 55 minutes exactly to make sure it has warmed up properly.

While it is doing that, I jack up the car and spin the wheels by hand then run to the drivers side and step on the brake.

I do this about 15 times to get a little bit of heat in to the brakes.

after 55 minutes have passed, I remove my tyre warmers and thermal blanket off the car and drive slowly, making sure I don't go over 0 on the boost gauge and not over 1500rpm on the tacho.. for at least the next 10 minutes.

At this point, it is safe to drive the car to a maximum of 3200rpm.. you don't want to thrash them over that..

Revs kills engines you know..

This routine takes about 12 hours each morning, but it is well worth it.

I strongly suggest you all do the same thing..

You would if you really cared about your skyline.

I take 12 hours and 30 minutes... can never be too careful :cheers:

oh and every 1/2 hour I replace the air filter element, I keep my boot jam packed with the suckers

What's boost?

I rarely use it... Probably about once a day I hit it, and it's due to a VERY poorly designed on ramp near me, speeds usually drop to 40 odd km/h in a 90 zone... Using 3rd gear I pull onto the outer lane with a decent amount of throttle (Mind you, I do it in a safe gap too!) and that's normally only low boost too.

I rarely hit full boost, maybe once or twice a week.

I just baby it, it's driven daily, and there's no need to hit full boost on the way to work.

yeh im with most ppl here... dont go over 3k till oil n water are up to temp. I never bother with warming up apart from getting up to oil pressure cos ur diff n trans dont get warmed up sitting there stationary! Most of my day to day driving is putting about off boost, with a squirt here and there. Dont usually get over 4k. I do however drive in the hills a couple times a week to blow the cobwebs out :P

^^^ You're getting a Handbag for xmas aren't you?

or maybe a towbar for the skyline so that you can tow your dresses.

No sweety, I'm just going to keep carrying yours around for you, as I don't want you to hurt yourself lifting something so heavy for you.

Seriously, it's a public road. The amount of people out there in peak hour traffic that jump and change. If you're hammering it, and they change lanes, it's an accident waiting to happen.

I actually found some good statistics not too long ago on the RTA site.

Approximately every 3 KM someone makes a mistake that could lead to an accident

Every 8KM someone makes a mistake leading to a near miss.

So if you drive 10km to work, you're bound to make 3 mistakes, with one leading to nearly having an accident.

You start flogging your car, those distances drop down quite a bit lower.

Wisen up or go buy your self a push bike

I actually found some good statistics not too long ago on the RTA site.

Approximately every 3 KM someone makes a mistake that could lead to an accident

Every 8KM someone makes a mistake leading to a near miss.

So if you drive 10km to work, you're bound to make 3 mistakes, with one leading to nearly having an accident.

You start flogging your car, those distances drop down quite a bit lower.

Wisen up or go buy your self a push bike

I've put those two words in bold, because it shows you dont know how to understand data. Someone out of XXXX amount of cars on the road makes a mistake every 3km. That doesn't mean that it is you

And I did buy a pushbike, thanks for asking :P

Sorry Jas, the stats actually was each average person.

I'll try find them again for you all. It was one person out of everyone, it was each person makes a mistake approx every 3km.

Each has a near miss approx every 8km.

Okay, got the stat SLIGHTLY wrong, but:

Crash research shows that all drivers, even

you, can and will make mistakes. It is estimated

that drivers make a mistake that:

Could lead to a crash about every three

kilometres.

Leads to a near crash about every 800

kilometres.

Leads to a crash about every 980,000

kilometres.

Page 30/31 of 94 of the Driver Qualification handbook

Start driving like a tool, you manage to lower those distances DRAMATICALLY!

Driving fast actually does save petrol,

unless you're coming up to a red light and still doing 70km/hr until 50 metres before it.

So I tend to accelerate faster than normal and go 5-10 above the limit unless overtaking

also shifting to neutral when going down steep declines helps a little :P

So if I drive 42km to and from work then it means I make 14 mistakes everyday?

Doesn't sound right to me, I mean even Mr Bean doesn't drive that bad

i never go over the speed limit. but ill do my best to get there as fast as possible.

i can't think of the last time i waited for my engine to warm up before hitting full boost.

limiter get a bashing daily.

stupid i guess, maybe ill learn when i have to replace the rb20. or crash.

when i drive normal cars(Camry) i drive granny spec, but when your behind the wheel of a skyline you can't help it!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...