Jump to content
SAU Community

Recommended Posts

Looking at getting some adj camber arms for f+r

Can only find places with Cusco/Tein for my car.

And i have checked Nengun/Greenline/PerfectRun

Where can i see some Ikeya Formula products?

Or do any of our sponsors stock these?

Cheers~

Link to comment
https://www.sau.com.au/forums/topic/196517-ikeya-formula/
Share on other sites

They seem to be good enough for street cars and low/mild track cars....we used the lower control arms for our r33 and ran out of adjustment and also found the balljoint was at the wrong angle, as soon as we went past -3 degrees of camber the balljoint bound up and wouldnt turn....had to modify the suckers so we could get a descent amount of adjustment out of them.

After using their lower control arms and finding how limited they were in adjustment, it makes me wonder just how 'good' their stuff really is, maybe im just more the type who would rather make their own stuff to suit the situation.

Check to see how much adjustability they offer before you buy them. For a street/road car application im sure it would be good enough.

Link to comment
https://www.sau.com.au/forums/topic/196517-ikeya-formula/#findComment-3524350
Share on other sites

i tend to agree. the ikeya stuff doesn't really blow me away quality wise. the cusco arms i have are much nicer then the ikeya once i have. cusco ones have bigger rose joints, better (3 piece, stainless, thick shell) rose joints and just seem nicer quality. but cusco don't make 32 GTR traction rods so i used ikeya for those. don't get me wrong, i wouldn't say they are crap, but they are not amazing either.

Link to comment
https://www.sau.com.au/forums/topic/196517-ikeya-formula/#findComment-3525314
Share on other sites

i tend to agree. the ikeya stuff doesn't really blow me away quality wise. the cusco arms i have are much nicer then the ikeya once i have. cusco ones have bigger rose joints, better (3 piece, stainless, thick shell) rose joints and just seem nicer quality. but cusco don't make 32 GTR traction rods so i used ikeya for those. don't get me wrong, i wouldn't say they are crap, but they are not amazing either.

nagisa-auto FTW :D top bloke great gear and get pissed whilst browsing :( i remmeber the lower arms and stuff i bought there about 5 years back... stunning and 20 beers later we managed to escape his shop.... the best thing about his shop was a little sign on the toilets... has anyone been there and seen it?

Link to comment
https://www.sau.com.au/forums/topic/196517-ikeya-formula/#findComment-3526066
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
×
×
  • Create New...