Jump to content
SAU Community

Recommended Posts

Looking at getting some adj camber arms for f+r

Can only find places with Cusco/Tein for my car.

And i have checked Nengun/Greenline/PerfectRun

Where can i see some Ikeya Formula products?

Or do any of our sponsors stock these?

Cheers~

Link to comment
https://www.sau.com.au/forums/topic/196517-ikeya-formula/
Share on other sites

They seem to be good enough for street cars and low/mild track cars....we used the lower control arms for our r33 and ran out of adjustment and also found the balljoint was at the wrong angle, as soon as we went past -3 degrees of camber the balljoint bound up and wouldnt turn....had to modify the suckers so we could get a descent amount of adjustment out of them.

After using their lower control arms and finding how limited they were in adjustment, it makes me wonder just how 'good' their stuff really is, maybe im just more the type who would rather make their own stuff to suit the situation.

Check to see how much adjustability they offer before you buy them. For a street/road car application im sure it would be good enough.

Link to comment
https://www.sau.com.au/forums/topic/196517-ikeya-formula/#findComment-3524350
Share on other sites

i tend to agree. the ikeya stuff doesn't really blow me away quality wise. the cusco arms i have are much nicer then the ikeya once i have. cusco ones have bigger rose joints, better (3 piece, stainless, thick shell) rose joints and just seem nicer quality. but cusco don't make 32 GTR traction rods so i used ikeya for those. don't get me wrong, i wouldn't say they are crap, but they are not amazing either.

Link to comment
https://www.sau.com.au/forums/topic/196517-ikeya-formula/#findComment-3525314
Share on other sites

i tend to agree. the ikeya stuff doesn't really blow me away quality wise. the cusco arms i have are much nicer then the ikeya once i have. cusco ones have bigger rose joints, better (3 piece, stainless, thick shell) rose joints and just seem nicer quality. but cusco don't make 32 GTR traction rods so i used ikeya for those. don't get me wrong, i wouldn't say they are crap, but they are not amazing either.

nagisa-auto FTW :D top bloke great gear and get pissed whilst browsing :( i remmeber the lower arms and stuff i bought there about 5 years back... stunning and 20 beers later we managed to escape his shop.... the best thing about his shop was a little sign on the toilets... has anyone been there and seen it?

Link to comment
https://www.sau.com.au/forums/topic/196517-ikeya-formula/#findComment-3526066
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
    • Being a manual, we very quickly ordered new R34 gearbox (From Nissan) and remaining parts from Kudos motorsports. Would highly recommend the team there. Ultra helpful and quick to share advice and upgrades. We are in the middle of taking the Auto out (Genuine 94,000/kms) and putting the Manual in this weekend. Part 2 of the build will include likely a Plazaman Intercooler and Plenium, Hks Exhaust with Tomei Dump (ordered).
×
×
  • Create New...